28
한국어
참고: 신체 부상을 초래하지 않는행위를
나타내며,방지하지않으면재산상의 손해가
발생할수 있습니다.
감전위험을나타냅니다.
화재위험을나타냅니다.
전동 공구에 관한 일반 안전 경고
경고: 안전 경고와 지시 사항을 모두 읽으십시오.
경고와지시사항을준수하지않으면감전,화재
및/또는심각한부상을초래할수있습니다.
향후 참고할 수 있도록 모든 경고 및 지시 사항을
보관해두십시오.
경고에서사용된"전동공구"라는용어는주공급전원에
의해전기가공급되는(유선)전동공구또는충전식(
무선)전동공구를의미합니다.
작업 영역 안전
작업 영역을 청결하고 밝게 유지하십시오.
혼잡하거나어두운작업장에서는사고가
발생하기쉽습니다.
가연성 액체, 가스 또는 먼지 등이 있는 폭발성
대기에서 전동 공구를 사용하지 마십시오. 전동
공구에서먼지나가스를발화시킬수있는불꽃이
튈수있습니다.
전동 공구로 작업하는 동안에는 어린이와 주변
사람들이 작업 영역에 가까이 들어오지 못하도록
하십시오. 주변이산만해져통제력을잃을수
있습니다.
전기 안전
전동 공구의 플러그는 콘센트와 형식이 일치해야
합니다. 플러그를 어떤 방식으로든 절대 개조하지
마십시오. 접지된(지면 접지) 전동 공구에 어떤
어댑터 플러그도 사용하지 마십시오. 개조되지
않은플러그및형식이일치하는콘센트를
사용하면감전위험이줄어듭니다.
파이프, 라디에이터, 렌지 및 냉장고 등과 같이
접지된 표면에 신체가 접촉하지 않도록 하십시오.
신체가접지되어있으면감전위험이높아집니다.
전동 공구를 비 또는 습한 환경에 노출하지
않도록 주의하십시오.전동공구에물이들어가면
감전위험이높아집니다.
코드를 함부로 다루지 마십시오. 코드를 사용하여
전동 공구를 운반하거나 잡아당기거나 플러그를
뽑지 마십시오. 열, 오일, 날카로운 모서리 또는
움직이는 부품에서 멀리 떨어진 장소에 코드를
보관하십시오. 코드가손상되거나얽혀있으면
감전위험이높아집니다.
전동 공구를 실외에서 사용할 때는 실외 사용에
적합한 연장 코드를 사용하십시오. 실외사용에
적합한코드를사용하면감전위험이줄어듭니다.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
4
English
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed orgrounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electricshock.
English (original instructions)
CORDLESS RECIPROCATING SAW
DCS388
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make
DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCS388
Max/Rating Voltage V
DC
60/54
Battery type Li-Ion
Max. power output W 1550
No load speed min
-1
0–3000
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/
plastic tubes
mm 300/130/160
Weight (without battery pack) kg 3.54
Battery pack DCB606 DCB546
Battery type Li-Ion Li-Ion
Voltage V
DC
20/60 18/54
Capacity Ah 6.0/2.0 6.0/2.0
Weight kg 1.05 1.05
Charger DCB118
Mains voltage V
AC
220-240
Battery type 20/60Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0,66
The DCB118 charger accepts 18/20V Li-Ion XR and
XRFLEXVOLT
TM
battery packs (DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185 DCB546 and DCB606).
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
ZV DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
4
English
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed orgrounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electricshock.
English (original instructions)
CORDLESS RECIPROCATING SAW
DCS388
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make
DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCS388
Max/Rating Voltage V
DC
60/54
Battery type Li-Ion
Max. power output W 1550
No load speed min
-1
0–3000
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/
plastic tubes
mm 300/130/160
Weight (without battery pack) kg 3.54
Battery pack DCB606 DCB546
Battery type Li-Ion Li-Ion
Voltage V
DC
20/60 18/54
Capacity Ah 6.0/2.0 6.0/2.0
Weight kg 1.05 1.05
Charger DCB118
Mains voltage V
AC
220-240
Battery type 20/60Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0,66
The DCB118 charger accepts 18/20V Li-Ion XR and
XRFLEXVOLT
TM
battery packs (DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185 DCB546 and DCB606).
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
ZV DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
충전 컷쏘
DCS388
축하합니다!
DeWALT공구를선택해주셔서감사합니다.DeWALT는
오랜경험과제품개발및혁신을통해전문전동공구
사용자들이인정하는기업으로자리잡아왔습니다.
기술 데이터
DCS388
최대/정격전압
V
DC
54
배터리유형 리튬이온
최대출력
W 1550
무부하속도
분-1 0–3000
스트로크길이
mm 28.6
나무/금속프로필/플라스틱
튜브에서의
절삭력
mm 300/130/160
무게(배터리팩제외)
kg 3.54
배터리팩
DCB546
배터리유형 리튬이온
전압
V
DC
18/54
용량
Ah 6.0/2.0
무게
kg 1.05
충전기
DCB118
전원전압
V
AC
220
배터리유형
20/60리튬이온
배터리팩의
대략적인충전
시간
분
22(1.3Ah) 22(1.5Ah) 30(2.0Ah)
45(3.0Ah) 60(4.0Ah) 75(5.0Ah)
60(6.0Ah)
무게
kg 0,66
DCB118충전기는18/20V리튬이온XR및XRFLEXVOLT
TM
배터리팩(DCB181,DCB182,DCB183,DCB183B,DCB184,
DCB184B,DCB185및DCB546을사용합니다.
경고: 부상위험을줄이려면사용설명서를
숙지하십시오.
정의: 안전 지침
다음정의는각경고문구의심각도를설명합니다.사용
설명서를읽고다음기호들에유의하십시오.
ZV위험:절박한위험상태를나타내며,방지하지
않으면사망 또는 심각한 부상을초래합니다.
경고: 잠재적위험상태를나타내며,방지하지
않으면사망 또는 심각한 부상을초래할수
있습니다.
주의: 잠재적으로위험한상태를나타내며,
방지하지않으면경미하거나 가벼운 부상을
초래할수 있습니다.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.