15
GB
4 Troubleshooting and technical data
4 Troubleshooting and technical data
4.1 Before you send in the appliance
Before contacting us or even sending the appliance to us, use the table to
check whether you can correct the problem yourself.
4.2 Warranty
The statutory warranty regulations in accordance with the EU Directive
1999/44/EC apply.
In non-EU countries the minimum requirements of the warranty in the re-
spective country apply.
4.3 Disposal
Dispose of the appliance in compliance with the environmental
protection laws of your country. Electrical waste may not be dis-
posed of together with domestic waste. Use local old-appliance
collection points instead.
The filters and dust filter bags are made from environmentally-friendly ma-
terials. You can dispose of them — as opposed to the appliance itself —
with your domestic waste, provided they do not contain anything that is for-
bidden from disposal in domestic waste.
4.4 Technical data
We reserve the right to make changes to
technical and design specifications in the in-
terest of continuous product improvement.
© Royal Appliance International GmbH
Risk of injury! Never use a faulty appliance! Always switch off the appli-
ance and disconnect it from the mains before starting troubleshooting.
Problem Possible cause / solution
Dust filter bag
change indi-
cator ap-
pears in the
window (Fig.
20).
The dust filter bag is full.
Change the dust filter bag, ZChapter 3.1, ‘Changing
the dust filter bag’.
The filters are dirty.
Clean the respective filter, ZChapter 3.2, ‘Cleaning /
changing the motor protection filter’ or ZChapter 3.3,
‘Cleaning/replacing the exhaust filter’.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long
wooden stick (e.g. a broomstick) to do this.
The vacuum
cleaner stops
suddenly.
The overheating protection has tripped (possibly due to
blocked suction channels, filters, or similar).
1. Switch the appliance off and pull the plug out of the
socket.
2. Remove the cause of overheating (e.g. by disas-
sembling telescopic tube and suction hose and re-
moving the obstacle and/or cleaning filters).
3. Wait around 45 minutes until the appliance has
cooled down.
4. After the appliance has cooled down, you may
switch it on again.
Problem Possible cause / solution
The cleaning
results are
unsatisfacto-
ry in spite of
the appliance
working cor-
rectly.
Bypass vent (Fig. 6) is open.
Close the bypass vent (Fig. 6).
Position of the suction power control is not appropriate
(Fig. 14).
Adjust the position of the suction power control (Fig.
14).
The attached nozzle is unsuitable.
Change the nozzle, ZChapter 2.1, ‘Assemble appli-
ance and adjust nozzles to surface’.
Collar brush of the floor nozzle is in a position that is
not appropriate for the floor (Fig. 8 – 9).
Adjust the position of the collar brush to the floor via the
switch on the floor nozzle (Fig. 8 – 9).
The dust filter bag is full.
Change the dust filter bag, ZChapter 3.1, ‘Changing
the dust filter bag’.
The filters are dirty.
Clean the respective filter, ZChapter 3.2, ‘Cleaning /
changing the motor protection filter’ or ZChapter 3.3,
‘Cleaning/replacing the exhaust filter’.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long
wooden stick (e.g. a broomstick) to do this.
If you cannot solve the problem using this table, contact the Dirt Devil
customer service department (ZPage 46, ‘International Service’).
Type of appliance : bagged vacuum cleaner
Model : M7003 (-0/-1/.../-8/-9)
Voltage : 220-240 V ~, 50/60 Hz
Power : 800 W
max. available dust bag capacity : approx. 1.5 litres
Power cord length : approx. 5 m
Weight : approx. 3.2 kg
M7003.book Seite 15 Freitag, 14. August 2015 12:26 12
To Next Page
Loading...
