DMP Electronics XTLtouch Lab Guide

7. Press a top-row select area to add a USER NAME and
press CMD
8. Press a top-row select area to select the USER LEVEL
9. Press CMD to save this user
ADD A USER CODE WITH CARD
1. At the keypad, press CMD until the USER MENU?
prompt displays
2. Select YES, enter 99+CMD to enter the USER MENU
3. Using CMD, navigate to USER CODES? and press a
top-row select area
4. Select ADD
5. Select the USER NUMBER and press CMD
6. Wave the card over the blue status LED
7. Press a top-row select area to add a USER NAME and
press CMD
8. Press a top-row select area to select the USER LEVEL
9. Press CMD to save this user
ARM & DISARM
1. Arm the system, trip an alarm and disarm
CHANGE THE SYSTEM TYPE TO H/S/A
1. Enter the panel programmer by entering 6653
(PROG) at the keypad
2. Navigate to SYSTEM OPTIONS and press a top-row
select area
3. Press a top-row select area to display the list of
system types
4. Select H/S/A as the system type
5. Exit SYSTEM OPTIONS, navigate to STOP to save
changes
6. Arm, disarm and trip an alarm in H/S/A system type
CHANGE THE SYSTEM TYPE TO AREA
1. Enter the panel programmer by entering 6653
(PROG) at the keypad
2. Navigate to SYSTEM OPTIONS and press a top-row
select area
3. Press a top-row select area to display the list of
system types
4. Select AREA as the system type
EDIT AREA NAMES
1. Press CMD to navigate to AREA INFORMATION
2. Press a top-row select area to enter AREA INFO
3. Enter an AREA NUMBER and press CMD
4. Press a top-row select area to clear any text and enter
in a new area name
5. Exit AREA INFORMATION and navigate to STOP to
save changes
6. Arm, disarm and trip an alarm in Area system type
ADD A Z-WAVE MODULE
1. At the keypad, press CMD until the USER MENU?
prompt displays
2. Select YES and enter 99+CMD to enter the USER
MENU
3. Using CMD, navigate to Z-WAVE SETUP? and press a
top-row select area
4. Select ADD
5. When the keypad displays ‘PRESS BUTTON ON
Z-WAVE DEVICE’ press the button on the front of the
lamp module
6. When the panel recognizes the device, it will display
‘DEVICE FOUND’
7. When the keypad displays ‘DEVICE ADDED’ press
CMD
8. Press a top-row select area to name this Z-Wave
device and press CMD
OPTIMIZE Z-WAVE
1. Navigate to the Z-WAVE SETUP menu and press CMD
to advance the list
2. Select OPT to optimize the signal
ê After adding any Z-Wave device, it is recommended to optimize Z-Wave
CREATE A FAVORITE
1. Navigate to the Z-WAVE SETUP menu and press CMD
to advance the list
2. Select FAV
3. Enter a favorite number and name
4. Choose which devices to include in the favorite
CREATE A FAVORITE SCHEDULE
1. At the keypad, press CMD until the USER MENU?
prompt displays
2. Select YES and enter 99+CMD to enter the USER
MENU
3. Using CMD, navigate to SCHEDULES? and press a
top-row select area
4. Select FAV to create a favorite schedule
5. Enter a FAVORITE NUMBER and press CMD
6. Select a day of the week and program the ACTIVATE
time
7. If this schedule will be following sunrise or sunset
times, press the second select area, then choose
SUNRISE or SUNSET.
ê Sunrise and Sunset times require a ZIP code to be entered in System Options
8. Continue this process for every day of the week
9. Press the BACK ARROW to exit the USER MENU
QUESTIONS
What else would you like to learn about the XTLtouch?
XTLtouch LAB GUIDE

DMP Electronics XTLtouch Specifications

General

Brand	DMP Electronics
Model	XTLtouch
Category	Security System
Language	English