Dometic RM 3662 - Startup Instructions; Shutting Off the Refrigerator

'98 lwi 46 141 238393
2 - WAY display panel.
B C
F
3 -WAY display panel.
A D
E
A.
B.
C.
1.
2.
3.
1.
2.
A continuous 12 volt DC supply must be available for
the electronic control to function.
Press the main power ON/OFF button (1) to the
DOWN
position.
Press the TEMPERATURE SELECTOR button (3)
P-WAY Model or (4)
3-WAY Model until the lamp at
the desired setting is Illuminated.
2-WAY MODEL
AUTO MODE
Press the AUTO/GAS mode selector button (2) to
turn ON the Auto lamp (D). If 120 volts AC is availab-
le, the AC mode indor lamp (B) will illuminate
indicating AC operation. If 120 volts AC is not avail-
abie, the GAS mode indicator tamp (C) will illuminate
and the control system will automatically switch to
GAS operation.
If the CHECK indicator lamp (E) illuminates and the
GAS mode indicator
lamp (C) is off, the controls have
failed to ignite the burner in the GAS mode. GAS
operation may be reset by pressing the main power
ON/OFF
button(l) to the OFF then ON position. (See
step 2 under GAS MODE).
Press the TEMPERATURE SELECTOR button (3)
until the
lamp at the desired position is iiiuminated.
FAS MO=
The refrigerator may be shut off while in any mode of
operation by pressing the main power ON/OFF button
to the UP (OFF) position. This shuts off ail DC power to
the refrigerator. inciudinc the interior iiaht.
Press the AUTO/GAS mode selector button (2) to
turn OFF the Auto lamp (D). The GAS mode
indicator
lamp (C)will illuminate. Within 45 seconds the burner
should be ignited and operating normaiiy.
On the initial refrigerator start-up, it may take longer
than 46 seconds to allow air to be purged from the
gas tine. if the gas does not ignite within 45 seconds
the CHECK indicator lamp (E) will illuminate and the
GAS mode indicator lamp (C) will go off. To reset
when the CHECK indicator lamp (E) is iiiuminated,
press the main power ON/OFF button (1) to the OFF
and then ON position.
3.
NOTE: Do not continue to reset GAS operation if the
CHECK indicator lamp continues to be illuminated
after several
tries.
Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired position is iiiurnlnated.
TO SHUT OFF THE REFRIGERATOR
START UP INSTRUCTIONS
1.
2.
3.
4.
1.
2.
3.
4.
1.
2.
3-WAY MODEL
AUTO MODE
Press the DC mode selector button (2) to turn OFF
the DC
lamp (A).
Press the AUTO/GAS mode selector button (3)
(ii required) to turn ON the Auto
lamp (D). If 120 volts
AC is available, the AC mode Indicator lamp (B) will
illuminate indicating AC operation. If 120 volts AC is
not avaiiabie, the GAS
mode indicator lamp (C) will
illuminate and the control system will automatically
switch to GAS operation.
if the CHECK indicator lamp
(E) illuminates and the
GAS mode indicator lamp (C) is off, the controls have
failed to ignite the burner in the GAS mode. GAS
operation may be reset by pressing the main power
ON/OFF button (1) to the OFF then ON position. (See
step 2 under GAS MODE).
Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is iiiuminated.
GAS MODE
Press the DC mode selector button (2) (if required)
to
turn OFF the DC lamp (A).
Press the AUTO/GAS mode selector button (3) to
turn OFF the Auto lamp (D). The GAS mode indicator
lamp (C) will illuminate. Within 45 seconds the burner
should be ignited and operating normally.
On the initial refrigerator start-up, it may take longer
then 45 seconds to allow air to be purged from the
gas
line. if the gas does not ignite within 45 seconds
the CHECK indicator lamp (E) will illuminate and the
GAS mode indicator lamp (C) will go off. To reset
when the CHECK indicator lamp (E) is illuminated,
press the main power ON/OFF button (1) to the OFF
and then ON position,
NOTE: Do not continue to reset GAS operation If the
CHECK indicator lamp continues to be illuminated
after several tries.
Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is illuminated.
DC MODE
Press the OC mode indicator button (2) to turn ON
the DC lamp (A).
Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is illuminated.