65
64
Banknote counter DORS 820 Banknote counter DORS 820
TABLE 4
Remove
banknotes
from the
stacker
The number of notes in the stacker
has reached the stacker capacity.
Take the banknotes out of the
stacker. The counter will resume
operation at once (in AUTO mode)
or after key I(II) is touched (in MAN
mode).
Remove
banknotes
from reject
pocket
The number of notes in the reject
pocket has reached reject pocket
capacity.
Take the banknotes out of reject
pocket.
Add
banknotes
The hopper is empty while the
number of notes in the stacker is
less than the required batch size (in
the AUTOMATIC START mode).
Add banknotes to the hopper, the
machine will resume counting.
Add
banknotes
and
press start
The hopper is empty while the
number of notes in the stacker is
less than the required batch size (in
the MANUAL START mode).
Add banknotes to the hopper,
touch key I(II).
Clean
the
pockets
Counting settings/modes were
changed after a count is finished.
Take the banknotes out of reject
pocket and the stacker.
Batch
is ready
A batch of required size is counted.
Take the banknotes out of the
stacker and continue counting.
Unavailable
You tried to choose the function
unavailable for the current counting
mode (for example, tried to choose
a currency in the COUNT mode or a
batch size in the MIX mode).
Change counting mode to activate
required option.
Self-testing.
Please wait
until the
process
is completed
The self-test is in progress. Wait until the message is closed.
Batch of XXX
notes is ready
where YYY
is in stacker
and ZZZ
are removed
The message appears when
selected batch size exceeds
stacker limit.
TABLE 4
Calibration.
Please wait until
the process
is completed
Auto sensors calibration is held on
after the counter is turned on and
every 30 minutes of operation
Can't feed the notes from the
hopper.
Wait until the message is closed.
Adjust the banknote guides to the
width of the widest note in the
batch. Adjust the feeder gap if
required («+» means gap increase)
for operation with thicker bank-
notes. To get the required gap, turn
screw 1 (Fig. 1) counter-clockwise.
There are
no banknotes.
Feed error
Settings reset acknowledgement
request
Reset
confirmation
The results of counted batch SN
detection are being saved in
counter memory
Wait until the message is closed.
Please wait
until the
process
is completed
TEMPORARY
SAVING OF
S/N READING
RESULTS
To prevent counter memory over-
flow while saving banknote SN
Three actions are possible:
1 Save stored SN data to PC and
clean counter memory from PC.
2 Clean counter memory from PC.
3 Touch «PLEASE DELETE
PREVIOUS RESULTS» to clean
counter memory
Confirm or cancel settings reset
(Fig. 44).
Error
message
Reason Teller's action
Error
message
Reason Teller's action
CONTENTS
FTP ERROR
Failed to
connect to
server Check
Ethernet
settings
and IP address
and FTP server
port
Incorrect FTP client or local
network settings. FTP server not
connected.
Make all the necessary settings and
connections* in the FTP tab of the SN
CONFIG menu, check the local
network settings (see the section
«Saving the data about the counted
banknotes to the computer»)
FTP ERROR
(530) Failed to
log in to the
server. Check
login and
password.
Login or password in the FTP tab
of the SN CONFIG menu does not
match FTP server data.
Check and, if necessary, change the
settings of the FTP server* (in case of
changing the settings reconnect the
Ethernet cable (see pos. 19 Fig. 2)).
Enter the correct username and
password in the FTP tab of the SN
CONFIG menu.
FTP ERROR
(550) The
specified folder
was not found.
Make sure it
exists and
reconnect the
network cable.
A destination folder to save the
archives is missing on the server.
Check and, if necessary, change the
settings of the FTP server* (in case of
changing the settings reconnect the
Ethernet cable (see pos. 19 Fig. 2)).
Enter the correct route to destination
folder.
* – Local network and FTP server settings must be adjusted by administrator.
To Next Page
Loading...
