TROUBLE SHOOTINGGUIDE
IT IS NOT NECE, =
THE:__MONITOR IS
;ARY TO RETURN THE ENTIRE TREADMILL FOR A MONITOR REPAIR
)VABLE FROM TREADMILL FOR REPAIR OR BATTERY REPLACEME'NT-
SEE PAGES 2 and 3.
,,ll=I I .....................
PROBLEM
,n Ji : .......... ' i ...........................
1. -Treadmill Will Not Siart.
Of Roller.
31'Tf._beltSiips_..h,eindSel..............
•-::::: ...................... t..... ..................... Miir IIIIIilIIIjIL]" ";j _"L ................
4. Tteadbett Hesitates When Stepped
On,
5. Treadmill Makes "Rum€ling" NoiSe.
i.'.Ti:e=_mi,ls0_utt ToRoii,...............
._-iai==kParticlesco,acingUnder
' Treadmill,
..........................
10. Monitor Ooee Not Display Speed Or
Distance,
II ]1iiilillllll i iiii iiii ii ii irl ir
11. Monitor Shuts Off.
12, No Pulse Displayed On Monitor
(See "Using The Pulse Pickup" On
Page 5),
CAUSE
1. - Not Plugged in.
Z ............
3,,_TreadmillReSetr,,$,.W_._,_..T_ped,
4. Unit Plugged Into InsufficientExten-
sion Co_,
#
e,"S_eedKno_NotTuine_TO
"SLOW',
The Treadbelt,
I, Treadbeit Tensioned Too High.
rreadl:)e_t.
1, Drive Belt IS Breaking in.
i. BatteriesAre Weak Or Dead,
i. Ree(I Switch Wire Not Connected
To Monitor.
2. Reed Switch Not Aligned Properly,
1, =Monitor Has Been Designed To
Shut Off After Four Minutes IfTread-
millisNot Operating.
2. net Damaaed Or Missing From
.. , ly on Pron_ Roller,
11Ul,..,, -: ..............................................................
3. Reed Switch Not Working Property,
I. Pulse Pickup Not Plugged into
Monitor.
2. Monitor Not In Pulse Mode.
31 'Purse Pickup Not Property AttaChed
To Eadot_e,
Much.
....€ORR,eC O ................
1, Plug Into Three Prong.(grounded}
1157120 Volt-60 Hz AGQutlet.
3. Reset Treadmill Reset Switch,
Short (less.Than _n=Fe=l, Heavy
Gauge (14 Gauge Qt Better) Exlen-
slonCoKl,
S( i;;iave QUaiji_dEl+ctrici_Checi<-
Voitage,
........TOoesired SpeeD, .................. ,..............
t. See *Storage And Maintenance"
Section Of Owners Manual.
...................................................... , ,,,r,,rr,, ,,r
1, See "Storage And Maintenance"
Section Of Owners Minual. '
.....
frea_belt,
TillNoise Ceases But Tree,belt
• Does Not SllpWhile In Use.
Ii e_a_si_Bi_ TOWi_*b_t_
Of T_e=dbelt.
1, Move To Hard Surface Or Low Cut
....carpetlng._...........................
1. vacuum Under Treadmill Pet._.
odlc,_lly ......._,'
1. Securely Piu¢I Reed Switch Wire
Into beck Of Monitor.
2. See "Storage And Matntenanee"
.....Sexton Of C_wne_ Manual,_:__:....
1, .OperateTreadmill And Check ForA
5j_ed Reading, If No Speed .Ols
2. Replace Magnet.
3, Replace Reed Switch.
1, Plug Pulse Pickup into Monitor ....
Z Place MO;iiiOi;]n Pulse MOde_ey-__
_Pres_tr_Mode Key Until Indicator IS.
.., Pointin_To Pu!sm...................................
3. a, Massage Earlobe To Increase
Circulation And Reattach Pulse
Pickup.
b, Massage And Attach PulSe Pick-
up To Ott_er Ea_obe.
• To Move Hea_ Erratically. See
0ETAiL "C" On Page 5.
IF OTHER PROBLEMS ARE ENCOUNTERED OR ANY OF THE ABOVE PROBLEMS CAN NOT BE
CORRECTED, CALL TOLL FREE: 1-800-633-5730 FOR SERVICE
To Previous Page
Loading...
General