To Next PageTo Next PageWhy is my Dreame Vacuum Cleaner not charging?
If your Dreame Vacuum Cleaner isn't charging, first ensure the base station is properly connected to power. Check that both ends of the power cord are correctly plugged in. Also, the charging contacts on the base station and the robot might have poor contact. Clean the charging contacts. Finally, check for and remove any foreign objects at the connector of the robot.
How to fix Dreame Vacuum Cleaner not connecting to Wi-Fi?
If your Dreame Vacuum Cleaner fails to connect to Wi-Fi, first ensure that the Wi-Fi password you're using is correct. The robot only supports a 2.4 GHz Wi-Fi connection, so ensure you're not trying to connect to a 5 GHz network. A weak Wi-Fi signal can also cause connection problems, so make sure the robot is in an area with good Wi-Fi coverage. Finally, the robot may not be ready to be configured, so exit and re-enter the app, and then try again as instructed.
Why is the charging speed of my Dreame Vacuum Cleaner slow?
If your Dreame Vacuum Cleaner charging speed is slow, ensure that the charging contacts on both the robot and the base are clean. Please wipe them with a dry cloth.
What to do if my Dreame Vacuum Cleaner won't turn on?
If your Dreame Vacuum Cleaner doesn't turn on, it might be due to a low battery. Recharge the robot on the base and try again. Alternatively, the battery temperature may be too low or too high. Ensure the appliance operates between 32°F (0°C) and 104°F (40°C).
What to do if my Dreame DreameBot L10s Pro Ultra Vacuum Cleaner moves without following the set route?
If your Dreame Vacuum Cleaner moves without following the set route, ensure that objects such as power cords and slippers are organized before using the robot. If the robot is working on wet, slippery surfaces, this can cause the main wheel to slip. It is recommended to dry the wet places before using the robot. Dirty or obstructed line laser sensors and the AI visual sensor can also cause this issue. Wipe them with a clean, soft cloth to keep them clean and unobstructed.
Why is my Dreame DreameBot L10s Pro Ultra so noisy?
If the noise increases while your Dreame Vacuum Cleaner is operating, it could be due to a clogged dust box filter. If so, clean or replace it. A hard object might be caught in the main brush or the dust box; check and remove any hard object. Also, the main brush or side brush may be tangled; check and remove any foreign objects. Alternatively, try switching the suction mode to Standard or Quiet.
What to do if Dreame DreameBot L10s Pro Ultra Vacuum Cleaner misses rooms?
If your Dreame Vacuum Cleaner misses rooms, first ensure that the doors to those rooms are open. Also, if the place in front of the room to be cleaned may be wet and slippery, please try drying the floor before using the robot.
Why can't my Dreame DreameBot L10s Pro Ultra Vacuum Cleaner find the base station?
If your Dreame Vacuum Cleaner cannot find and return to the base station, there may be too many obstructions around the base station. Place the base station in a more open area. If the robot is too far from the base station, you will need to manually place the robot onto the base station. Also, the signaling area on the base station may be dusty or debris-filled. Wipe the signaling area on the base station to remove dust or debris.
General| Battery Capacity | 5200 mAh |
|---|---|
| App Control | Yes |
| Mopping Function | Yes |
| Obstacle Avoidance | 3D Structured Light |
| Auto Empty | Yes |
| Auto Mop Washing | Yes |
| Auto Water Refill | Yes |
| Auto Detergent Dispensing | Yes |
| Auto-Empty Station | Yes |
| Multi-floor Mapping | Yes |
| Virtual Boundaries | Yes |
| Scheduled Cleaning | Yes |
| Run Time | Up to 180 minutes |
| Water Tank Capacity | 80 ml |
| Mapping | Yes |
| Voice Control | Yes |
| Operating Time | Up to 180 minutes (in quiet mode) |
| Auto Drying | Yes |
| Carpet Detection | Yes |
Essential safety precautions for operating the appliance.
Proper grounding procedures for electrical safety and preventing shock.
List of items included in the product package.
Overview of buttons, lights, and status indicators on the robot.
Identification and location of robot sensors and components.
Identification and location of base station parts.
Steps to prepare the home environment and remove potential obstacles.
Guidelines for positioning the base station for optimal operation.
Instructions for placing the robot and filling tanks.
Guide to downloading and setting up the mobile application.
Instructions for starting, stopping, and managing robot functions.
Explanation of special cleaning modes like DND and spot cleaning.
How to use the robot's vacuuming and mopping features.
Instructions for auto-empty, mop washing/drying, and specific cleaning modes.
How to clean the used water tank to prevent odors.
Steps for cleaning the base station and replacing the dust bag.
Maintenance for used water tank, brushes, dust box, and filter.
Instructions for cleaning the omnidirectional wheel and sensors.
How to clean robot sensors, charging contacts, and vents.
Replacing mop pads and general battery care advice.
Solutions for robot not turning on, charging, or operating correctly.
Fixing Wi-Fi connection, base station, and movement issues.
Addressing issues with auto-empty and water levels.
Technical details for the robot and base station.
Procedures for safe battery removal and environmentally responsible disposal.
