Why my Dreame DreameBot L10s Pro Ultra Heat is not charging?
If your Dreame Vacuum Cleaner robot is not charging, check that the base station is properly connected to power by ensuring both ends of the power cord are correctly plugged in. Also, clean the charging contacts to ensure good contact between the base station and the robot. Finally, inspect the connector of the robot for any foreign objects and remove them if present.
What to do if my Dreame DreameBot L10s Pro Ultra Heat Vacuum Cleaner will not turn on?
If your Dreame Vacuum Cleaner robot will not turn on, it might be due to a low battery. Recharge the robot on the base and try again. Alternatively, the battery temperature may be too low or too high. It is recommended to operate the appliance at a temperature between 32°F (0°C) and 104°F (40°C).
What to do if my Dreame DreameBot L10s Pro Ultra Heat Vacuum Cleaner cannot return to the base station?
If your Dreame Vacuum Cleaner robot cannot find its way back to the base station, make sure the base station is connected to power. If the base station was moved while the robot was not on it, this could also be the reason. Ensure the area around the base station is open and free of obstructions. If the robot is too far away, manually place it on the base station. You may also wipe the signaling area on the base station to remove any dust or debris.
Why Dreame DreameBot L10s Pro Ultra Heat Vacuum Cleaner station cannot automatically empty the dust box?
If the Dreame Vacuum Cleaner station isn't automatically emptying the dust box, start by checking if the dust bag in the dust tank is full and replace it if necessary. Also, inspect the auto-empty vents of the robot, the base station, and the dust box for any obstructions, and clean them if found.
Why the noise increases while Dreame DreameBot L10s Pro Ultra Heat is operating?
If the noise increases while your Dreame Vacuum Cleaner robot is operating, the dust box filter may be clogged. Clean or replace the filter.
Why Dreame DreameBot L10s Pro Ultra Heat Vacuum Cleaner will not resume cleaning after charging?
If your Dreame Vacuum Cleaner robot will not resume cleaning after charging, check to see if it is set to Do Not Disturb (DND) mode. If it is, disable DND mode.
Why Dreame Vacuum Cleaner charging speed is slow?
If your Dreame Vacuum Cleaner's charging speed is slow, keep in mind that fully charging a robot with a low battery takes about 3.5 hours. If you operate the robot at temperatures outside of the specified range, the charging speed will automatically slow down to extend the battery life.
Why Dreame Vacuum Cleaner moves without following the set route?
If your Dreame Vacuum Cleaner robot isn't following the set route, it may be due to objects such as power cords and slippers in its path. Please organize these objects before using the robot.
Why Dreame DreameBot L10s Pro Ultra Heat misses the rooms to be cleaned?
If your Dreame Vacuum Cleaner robot is missing rooms during cleaning, first ensure that the doors to those rooms are open. Also, the robot cannot climb over high thresholds or steps, so if there is a threshold higher than 2 cm at the door of the room, this could be the reason.
What to do if Dreame DreameBot L10s Pro Ultra Heat will not turn off?
If your Dreame Vacuum Cleaner robot will not turn off, it may be because it cannot be turned off when it is charging. It is recommended to move the robot from the base station, and then press and hold the button for 3 seconds to turn it off.
General| Brand | Dreame |
|---|---|
| Model | DreameBot L10s Pro Ultra Heat |
| Category | Vacuum Cleaner |
| Language | English |
General safety guidelines and prohibitions for operating the appliance.
Guidelines for safe battery handling and charging practices.
List of items included in the robot's package.
Detailed diagrams of the robot and base station parts.
Instructions for preparing the cleaning area and ensuring safety.
Connecting power, placing the base station, and installing ramp.
Installing side brush, mop, and preparing water/cleaning solution.
Steps to download the app and connect the robot to Wi-Fi.
Fast mapping, power, pause, auto-resume, DND, spot cleaning, and restarting.
Operating vacuum-only, mop-only, or combined vacuum-mop tasks.
Recommended frequency for cleaning/replacing robot and base station parts.
Instructions for cleaning the base station, including washboard and water.
Procedures for discarding dust bags and cleaning the filter.
Cleaning the used water tank and main brush.
Cleaning the omnidirectional wheel, sensors, and charging contacts.
Replacing mop pads and maintaining battery health.
Detailed specifications for the robot and its base station.
Guidelines for removing and disposing of the robot's battery safely.
Information on the proper disposal of waste electrical and electronic equipment.
To Next Page