Dremel 760 - Power Tool Use and Care; Battery Tool Use and Care; Service

-3-
989>+>>/7:>>9.3=+==/7,6/
>2/,+>>/<C9< </79@/ +8C
-
97:98/8> :<94/->381 0<97 >2/ ,+>>/<C
>/<738+6= Fire or injury may result. Prior to
disposal, protect exposed terminals with heavy
insulating tape to prevent shorting.
3>23?7398+>>/<3/=
If equipped with a lithium-ion battery, the battery
must be collected, recycled or disposed of in
an environ mentally sound manner.
“The EPA certified RBRC Battery
Recycling Seal on the lithium-ion
(Li-ion) battery indicates Robert
Bosch Tool Corporation is
voluntarily participating in an industry program
to collect and recycle these batteries at the
end of their useful life, when taken out of
s
ervice in the United States or Canada. The
RBRC program provides a convenient
alterative to placing used Li-ion batteries into
the trash or the munici pal waste stream, which
may be illegal in your area.
Please call 1-800-8-BATTERY for information
on Li-ion battery recycling and disposal
bans/restrictions in your area, or return your
batteries to a Skil/Bosch/Dremel Service
Center for recycling. Robert Bosch Tool
Corporation’s involvement in this program is
part of our commitment to preserving our
environment and conserving our natural
resources.”
!
WARNING
0 +8 /B>/8=398 -9<. 3=
8/-/==+<C + -9<. A3>2
+./;?+>/ =3D/ -98.?->9<= >2+> 3= -+:+,6/
90-+<<C381>2/-?<</8>8/-/==+<C09<C9?<
>996 7?=> ,/ ?=/. This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles
.
 $The smaller the gauge number, the
heav i er the cord.
" #*# ($#  "#
& $$"$%""$$ #
!
WARNING
$996G=
7:/</
"+>381
9<.#3D/38'
'3</#3D/=3877

3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
9<./81>238//> 9<./81>238/>/<=
1. The charger was designed to fast charge
the battery only when the battery temperature
is between 32˚F (0˚C) and 113˚F (45˚C). If the
battery pack is too hot or too cold, the charger
will not fast charge the battery. (This may
happen if the battery pack is hot from heavy
use). When the battery temperature returns to
between 32˚F (0˚C) and 113˚F (45˚C), the
charger will automatically begin charging.
2. A substantial drop in operating time per
charge may mean that the battery pack is
nearing the end of its life and should be replaced.
3. Remember to unplug charger during storage
period.
4. If battery does not charge properly:
a. Check for voltage at outlet by plugging in
some other electrical device.
b. Check to see if outlet is connected to a
light switch which turns power “off” when lights
are turned off.
c. Check battery pack terminals for dirt.
Clean with cotton swab and alcohol if
necessary.
d. If you still do not get proper charging,
take or send tool, battery pack and charger to
your local Dremel Service Center. See “Tools,
Electric” in the Yellow Pages for names and
addresses.
9>/ Use of chargers or battery packs not
sold by Dremel will void the warranty.
+>>/<C3=:9=+6
B>/8=3989<.=
7:9<>+8>2+<13819>/=
SM 2610031419 02-13_SM 2610031419 02-13.qxp 2/28/13 2:41 PM Page 3