Dremel Micro 8050 - Cutting Accessories

29
*@554*5DD9>7C?>D9>E54
1D1<?7 *?6D 1B4 #1=9>1D5C *D55< <E=9>E= *85<< 5B1=93 <1CC
%E=25B .??4 .??4 '<1CD93 B1CC5D3 *D?>5
453, 454, -- -25-30 ----
455
819>*1G*81B@5>9>7*D?>5C
1D1<?7 *?6D 1B4 #1=9>1D5C *D55< <E=9>E= *85<< 5B1=93 <1CC
%E=25B .??4 .??4 '<1CD93 B1CC5D3 *D?>5
461, 462, 463 -- -18-24 18-24 18-24 18-24 18-24
414, 422, 429 -- -12-17 12-17 12-17 12-17 12-17
425, 427 -- -18-24 18-24 ---
423E -- -12-24 5-8 5-8 5-8 12-24
'?<9C89>7335CC?B95C
1D1<?7 *?6D 1B4 #1=9>1D5C *D55< <E=9>E= *85<< 5B1=93 <1CC
%E=25B .??4 .??4 '<1CD93 B1CC5D3 *D?>5
430, 431, 438 5-30 5-30 5-17 25-30 25-30 5-30 5-30 -
439, 440, 444 5-30 5-30 5-17 25-30 25-30 5-30 5-30 -
407, 408, 432 5-30 5-30 5-17 25-30 25-30 5-30 5-30 -
411, 412, 413 12-17 12-17 5-8 - 5-8 ---
*1>49>71>4C1>49C3C
1D1<?7 *?6D 1B4 #1=9>1D5C *D55< <E=9>E= *85<< 5B1=93 <1CC
%E=25B .??4 .??4 '<1CD93 B1CC5D3 *D?>5
409, 420, 426 -- 15 25-30 25-30 25-30 25-30 -
540, EZ409
543, EZ544 25-30 18-30 15 -----
545, EZ545 18-30 18-24 -- -12-24 12-24 -
560 For use on drywall. For best results, use at 30,000 rpm.
561 12-30 12-30 15 - 25-30 ---
562 -- - - - -25-30
EZ456 -- -25-30 25-30 ---
EZ476 - - 15 -----
EDD9>7335CC?B95C
* Speed for light cuts; 1ED9?> - burning on deep grooves.
• Depending on cutting direction relative to grain.
%?D5138>E=25BC5DD9>7C<9CD549>D85C@554381BDCH)'$RC
1D1<?7 *?6D 1B4 #1=9>1D5C *D55< <E=9>E= *85<< 5B1=93 <1CC
%E=25B .??4 .??4 '<1CD93 B1CC5D3 *D?>5
403, 404, 405 9-11 9-11 5-11 12-15 5-8 ---
428, 442, 443 9-11 9-11 5-8 9-11 9-11 ---
530, 531, 532 - 9-11 - 9-11 ----
535, 536, 537 9-11 9-11 - 9-11 9-11 9-11 --
.9B5BEC85C
DM 2610031565 05-14-v8_8050 5/13/14 11:46 AM Page 29