EasyManua.ls Logo

DSC PC5516Z

DSC PC5516Z
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
System Introduction
S E C T I O N 1
1.1 Specifications
Control Panel Specifications
Flexible Zone Configuration:
8 Fully Programmable Zones
38 Access Codes: 32 User, 1 System Master, 2 Partition Master, 2 Duress and 1 maintenance
Expandable to 32 Zones
Keypads with zone inputs available (PC/KP5508Z, PC/KP5516Z, PC/KP5532Z, LCD/KPL5500Z)
Hardwired expansion available using the PC5108 Eight Zone Expansion module, the PC5700 Fire
module, or the PC5720 Fire and DVACS module.
Wireless expansion available using the PC5132 Wireless Zone Expansion module (up to 32 wireless
zones, 900MHz, True Spread Spectrum Technology, Fully Supervised)
Normally Closed, Single EOL, or Double EOL zone supervision
2-Wire Smoke Input (via PGM2 input)
27 Zone Types, 8 Programmable Zone Options
2 Partitions
Audible Alarm Output:
Supervised Bell Output (current limited at 3 amps), 12 V
DC
Steady or Pulsed Output
EEPROM Memory:
Will not lose programming or system status on complete AC and Battery failure
Programmable Outputs:
Up to 14 Programmable Voltage Outputs, 23 programmable options
One High Current (300 mA) PGM output with 2 wire smoke detector capability on main panel
Maximum Loop Current is 1.5 mA when the 2-wire smoke detector configuration is used
One Low Current (50 mA) PGM output on main panel
Eight Additional Low Current (50 mA) PGM outputs available using the PC5208 module
Four High Current (1 Amp) PGM outputs Available Using the PC5204 module
1 PC5204 Output Fully Supervised for Siren Output
Powerful 1.5 Amp Regulated Power Supply:
500 mA Auxiliary Supply, 12 V
DC
Positive Temperature Coefficient (PTC) components replace fuses
Supervision for loss of AC Power, Low Battery
Internal Clock Locked to AC Power Frequency
Power Requirements:
Transformer = 16.5 VAC, 40VA
Battery = 12 volt 4 Ah minimum rechargeable sealed lead acid
Remote Keypad Specifications:
8 Different Keypads Available:
- PC5508(Z)/KP5508(Z) 8 Zone LED Keypad - PC5532(Z)/KP5532(Z) 32 Zone LED Keypad
- PC5516(Z)/KP5516(Z) 16 Zone LED Keypad - LCD5500(Z)/KPL5500(Z) Alphanumeric Keypad
Each Keypad has 5 Fully Programmable Function Keys Connect up to 8 Keypads
Four Wire (Quad) Connection to Keybus Built in Piezoelectric Buzzer
Digital Communicator Specifications:
Supports all Major Formats including SIA and Contact ID Event Initiated Personal Paging
3 Programmable Phone Numbers 2 Account numbers
Supports LINKS1000 Cellular Communication DTMF and Pulse Dialing
DPDT Line Seizure Anti-jam Feature
Split Reporting of Selected Transmissions to Each Telephone Number
System Supervision Features
The PC5010 continuously monitors a number of possible trouble conditions including:
AC Power Failure Trouble by Zone Fire Trouble
Telephone Line Trouble Low Battery Condition Bell Output Trouble
Loss of Internal Clock AUX Power Supply Fault Tamper by Zone
Failure to Communicate Module Fault (Supervisory or Tamper)

Table of Contents

Other manuals for DSC PC5516Z

Question and Answer IconNeed help?

Do you have a question about the DSC PC5516Z and is the answer not in the manual?

DSC PC5516Z Specifications

General IconGeneral
ModelPC5516Z
TypeKeypad
ConnectionWired
Zones16
DisplayLCD
Keypad Zones16
WirelessNo
Power Supply12V DC
BacklightYes
Number of Keys16
Voltage12 VDC
Current50 mA
Supports up to16 zones
CompatibilityDSC PowerSeries
Operating Temperature32°F to 120°F (0°C to 49°C)

Summary

Specifications

Control Panel Specifications

Detailed specifications for the control panel's features and capabilities.

Additional Devices

Keypads

Information on available keypads and their specifications.

PC5132 Wireless Receiver Module

Details on the wireless receiver module for adding wireless devices.

Installation Steps

Terminal Descriptions

Keybus Operation and Wiring

Assigning Zones to Zone Expanders

Keypad Assignment

How to Assign Keypads

Procedure for assigning keypads to specific slots and partitions.

Enable Supervision

Zone Wiring

Normally Closed (NC) Loops

Details on wiring normally closed zone loops for supervision.

Double End of Line (DEOL) Resistors

Wiring instructions for double end-of-line resistors for zone supervision.

Access Codes

ArmingDisarming

[*] Commands

[*]+[1] Zone BypassReactivate StayAway Zones

How to bypass or reactivate zones using keypad commands.

[*]+[2] Trouble Display

Viewing system trouble conditions via the keypad.

Function Keys

Function Key Options

Explains the various functions assignable to keypad function keys.

How to Enter Installer Programming

Zone Definitions

Communicator - Reporting Formats

Contact ID

Details on the Contact ID reporting format for central station communication.

Downloading

PGM Outputs

PGM Output Options

Explains the various programmable output options and their functions.

Telephone Line Monitor (TLM)

Fire, Auxiliary, Panic Keys

LINKS1000 Cellular Communicator

Using LINKS1000 as the Sole Communicator

How to use the LINKS1000 as the primary communication method.

Default (Factory)

Factory Default Main Panel (Hardware)

Procedure for performing a hardware factory default on the main panel.

Walk Test (Installer)

Appendix A - Contact ID

Related product manuals