DT Research DT362 - Operation and Configuration; Internal Battery Switch and Powering; Start Up Procedure; Device Configuration Options

DT362
ENGLISH
4
5
ENGLISH
OPERATION
Internal Baery Switch
To prevent baery drain during shipping and extended storage, the internal baery may
be disconnected. To connect the internal baery, push the baery buon switch (on the
back panel) to the
“
up
”
posion (see page 2 for photo). The internal baery pack has to
be connected for it to operate, be charged, and for the oponal external baery pack to
funcon.
Powering ON and OFF
To acvate the DT362, push and quickly release the Power Buon. The display will come
on in a few seconds. To put the DT362 in Standby mode, push and quickly release the
Power Buon. To turn the DT362 off for extended storage, power off the device safely
using any soware funcon that
“
shuts down computer
”
provided in the soware
operang system.
NOTE: The baery packs shipped with you
r device may be low in power
—
please use
the AC-DC adapter with the DT362 when seng up the device for the first me to
fully charge the internal baery pack. You may charge the external baery pack with it
aached to the DT362, or with the oponal external baery charger kit.
NOTE: When the baery pack(s) is (are) charging, the blue-colored Baery LED should
blink slowly. If plugging in the AC-DC ad
apter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally. Try
unplugging/ replugging the AC-DC adapter to the DT362 a few mes to acvate the
charging process.
NOTE: To conserve power, use (push and quick release) the Power Buon to put the
device in
“
Standby
”
mode while not in use. Pushing briefly on the same buon will wake
up the s
ystem within seconds.
NOTE: Avoid using the Power Buon (
“
hold 4+ seconds
”
feature) to turn off the
device
—
this form of hardware shutdown is intended to be a means of recovery from
device lockups, and not as normal operaon.
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface will be
displayed aer a launch sequence of several seconds. The wireless LAN connec
on may take
10-15 seconds to be established.
Configuring the DT362
The device may be configured using the ulies and methods dictated by the soware
operang system. The DT362 should be configurable for various properes such as user
profiles, network features, and several system elements.
Calibraon
The touch display for the DT362 is calibrated before shipping. In the event that the
calibraon has been
modified or is unsasfactory, the respecve calibraon rounes
(e.g., PenMount (PM) for Windows XP) to calibrate the touch interface may be used.
Such applicaons are typically executed through touch input via Stylus or through mouse
click via a USB mouse.
Wireless Networking
Wireless LAN
The DT362 is oen delivered with an embedded (user-inaccessible) 802.11a/b/g/n
WLAN adapter equipped with a hidd
en custom antenna.
T
• hrough the support of typical WLAN adapters, the DT362 should be able to detect
all 802.11 access points in the vicinity for you to select the access point of your
choice for connecon.
T
• he SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT362 and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or
advanced alternaves) for secure
access.
W
• hen WEP/WPA/WPA2 is enabled, you may need to consult your network admin-
istrator or your networking equipment literature to properly configure associated
sengs such as Authencaon mode, etc.
R
• efer to the access point operang manuals for seng up the 802.11 access points.