Dual CT 7040 - Program Storage; Stored Station Recall; Mono Mode Operation

— Press button «0» of assembly 2 the display becomes
FM 100 e — — MHz.
— Press button «8» of assembly 2 the display becomes
FM 100 e 8 — MHz.
— Press button «5» of assembly 2 the display becomes
FM 100 e 85 MHz.
Program storage
Your receiver enables you to store 40 different stations, either in AM or
FM, plus the last stations called by the AM and FM buttons, i.e. a total
of 42 stations.
There is a choice of two storage methods:
— By entering the number of the chosen program.
— By automatic selection of the program number.
a) By entering the program number
— Search for the desired station, either by automatic or manual search,
or by direct call of the freguency.
— Press button 2.
(The freguency, shown in the display, will flash.)
— Enter the desired program number using buttons «1» to «0» of
assembly (2).
Access to programs 1 to 9 and 40:
Press one of the 10 buttons of assembly 2 corresponding to the
program selected.
Access to programs 10 to 19; 20 to 29; 30 to 39:
— Press and hold down (for more than 0.7 second) one of the buttons
«1», «2», «9» of assembly (2).
The display 2 shows: either Pr 1 — or Pr 2 — or Pr 3 —.
— Press one ofthe 10 buttons «1» to «0» of assembly 2 to complete the
program number selected.
For a few seconds the relative program number is shown in the
display: then the station freguency reappears.
— Proceed in the same way to store the other stations.
b) By automatic selection of the program number
This unit enables you to store a station automatically in the first vacant
memory. To do so, proceed as follows:
— Search for the desired station either by automatic or manual search,
or by direct call of the freguency.
— Press the memory button 4 (the freguency, shown in the display, will
flash).
— Press button 4 again.
The freguency displayed is now stored in the vacant program
number which will be indicated once storage operations are com-
plete. Afterwards, the display shows the freguency again.
— Proceed in the same way to store the other stations.
Important:
— |f all the memories are in use, the unit will indicate «FULL» when
button 4 is pressed twice.
No further storage operations can be performed automatically.
Storage can only now be performed by entering the program
number. The station previously stored on the same program
number will now be erased.
— You can also erase the contents of the 40 programs by pressing;
button (4) for more than 5 seconds.
You can now store the 40 stations, in succession, in programs 1 to!
40.
— You can also check if a memory is vacant, by calling the appropriate
program number. If the memory is vacant, the display will show
sign «000».
Note: whichever storage method is used.
— A station cannot be stored unless the frequency on display is
blinking. j
— The stations remain stored even if the power plug is disconnected
from the set. For this purpose, your set contains a lithium battery:
with a life of more than 10 years. Only a specialist can change tl
battery since this requires reprogramming intermediate frequencies.
for the built-in microprocessor.
Listening to a station which has been stored
Call the desired program using buttons «1» to «0» of assembly (2).
Program/frequency button
Each time button 9 is pressed, the display «Frequency/Program `
changes.
The program displayed is that selected previously (1 to 40) without
taking into account the two stations stored on «AM» or «FM». y
When a program is displayed «Pr 1 to 40», another program can Dë
selected.
Manual search
— Press button 6 to erase «AUTO» if the latter appears in the display,
— Press button 7 or 8. 1
Automatic search
— If «AUTO» does not appear in the display, press button 6 to make iti
appear.
— Press button 7 or 8: program search takes place in one direction 0
the other.
— To stop search on the desired program number: press button 6.
Any time the AM or FM button is pushed, the display returns to
frequency mode and shows the last station selected on each of these
two buttons.
Mono mode
Stereophonic listening is only possible in freguency modulation whe
the display shows that the station is broadcast in stereo.
— Indication «FM STEREO»:
Stereophonic broadcast; stereophonic listening.
When reception of a station is poor, we advise you to listen in mong
to eliminate hiss.
To do so, press button 5. The display will indicate mono mode.
— Indication «FM STEREO» and «MONO»:
Stereophonic broadcast; mono listening.
Remarks:
— The mono mode, plus the wavelength and the station frequen
remain stored.
— The «MONO» indication can be erased by pressing button 5 agai