Dynatronics Dynatron 925

To Next Page

To Previous Page

CAN/CSA WAVEFORMREQUIREMENTS

DYNATRON® 25 SERIES™ | OPERATOR’S MANUAL 95

Hi Volt

Mid-Range Full Range

500 ohm Load 200 ohm Load 1000 ohm Load

2000 ohm Load

Main Page

Default Chapter3
- Table of Contents3
Introduction to the Dynatron® 25 Series7
- Summary of Features by Device7
- Simplified Setup8
- Language Selection8
- Operator's Profile8
Feature8
- Before You Treat a Patient9
Installation and Features10
- Unpacking10
- Standard Components10
Dynatron® 25 Series Physical Features13
- Premod15
- Biphasic15
- Russian15
Electrotherapy Information and Usage Cautions27
Interferential / Premodulated Instructions31
- Detailed Interferential / Premodulated Setup31
Interferential and Premodulated Modality Information35
- Interferential (Quadpolar) Therapy35
- Premodulated (Bipolar) Therapy36
- Target36
- Why Is Target Better36
- Target Sweep37
- Interferential Electrode Placement37
- Interferential / Premodulated Default Settings37
- Interferential Default Settings37
- Premodulated Default Settings37
Biphasic / Russian Instructions38
- Biphasic / Russian Quick Setup39
- Detailed Biphasic / Russian Setup40
Biphasic / Russian Modality Information43
- Russian Stimulation43
- Biphasic Stimulation43
- Biphasic / Russian Parameters and Defaults43
High Volt Instructions46
- High Volt Electrode Setup46
- High Volt46
  - Detailed High Volt Setup47
  - High Volt Quick Setup47
High Volt Modality Information51
- High Volt Waveform51
- High Volt Settings51
- High Volt Default Settings52
- High Volt Waveform Specifications52
Ultrasound Instructions53
- Ultrasound53
Ultrasound Modality Information59
- Selecting the Appropriate Soundhead59
- Penetration of Ultrasound Waves60
- Types of Delivery61
- Treatment Time61
- Treatment Intensity61
- Frequency of Treatment62
- Usage Cautions - Combination Treatments62
- Potential for Burns or Periosteal Pain62
Ultrasound Problem Solving64
- Whirlpool Treatments64
- Soundhead Temperature too Cold64
- No Soundhead65
- Miscellaneous65
- Replacing the Soundhead65
- Ultrasound Specifications66
- Ultrasound Regulation and Technical Information66
Ultrasound Beam Profiles67
Combination Therapy Instructions69
- Comboplus69
- Stim through the Soundhead70
- Combination Therapy Setup71
- Modify a Treatment72
- Combination Default Settings72
Simultaneous Treatments73
- Set up a Second Treatment73
- Modify Simultaneous Treatments73
Contraindications, Warnings, & Precautions75
- Contraindications75
- Warnings75
- Precautions76
- Treatment Setup Warnings77
- Adverse Effects77
Contraindications, Warnings, & Precautions for Ultrasound Treatment79
- Contraindications79
- Precautions80
- Warnings81
Technical Information82
- Setting Defaults82
- Save New Defaults82
- Restore Factory Defaults83
Battery Operation84
- Battery Life85
General Specifications86
- Dynatron 25 Series Specifications86
- Environmental Conditions86
- Safety Features of the Dynatron 25 Series87
- Care and Cleaning Instructions87
- Suggested Maintenance Schedule88
- Routine Ultrasound Calibration Inspections for 25 Series89
- Software Updates90
- Returning a Unit for Repair91
- Definition of Symbols and Labeling92
- Equipment Classification93
- Disposal of Equipment and Accessories93
Basic Troubleshooting Techniques94
- Lead Testing94
- Testing Carbon Pads95
CAN/CSA Waveform Requirements96
Electromagnetic Emissions and Immunity102
Medical Device Reporting Requirements106
- Definition of Serious Injury106
- Reporting any Incident of Patient Discomfort107
Dynatron® 25 Series Plus Limited Warranty108
- 25 Series Warranty Registration109

Dynatronics Dynatron 925 - Page 101

Table of Contents

Related product manuals