DX-AC1200
1200mA Universal AC Adapter
Adaptateur c.a. universel de 1 200 mA
Adaptador universal de CA de 1,200 mA
Package contents
• 1200mA universal AC adapter
• Quick Setup Guide
Getting started
1 Set the voltage selector switch to the proper setting for
your device. Refer to the device’s user manual for the correct
voltage requirement, or determine the voltage by
multiplying the number of batteries required by 1.5.
(Example: 4 batteries × 1.5=6 volts)
Note: A device’s voltage setting may also be found next to the DC
jack or on a device information plate.
2 Select the adapter plug tip that best ts the device.
3 Insert the correct adapter plug tip into the AC adapter
connector.
4 Connect the adapter plug tip into the DC jack of your device.
5 Plug the AC adapter into a 110-240V standard electrical
outlet and and use the device as usual.
Important: This adapter is intended to be correctly
oriented in a vertical or oor mount position.
6 If your device does not work, immediately unplug the AC
adapter and recheck the instructions carefully, particularly
the voltage and polarity setting.
Quick Setup Guide / Guide d’installation rapide / Guía de instalación rápida
Cautions
• Never attempt to power a device for which the voltage or
polarity is unknown. Improper voltage or polarity settings
may result in severe damage to the device or AC adapter.
• This adapter should never be used with any device that
requires more than 1200mA of current.
• Disconnect the AC adapter from the electrical outlet when
not in use.
Specications
Input voltage: AC100-240V 60/50Hz
Input plug: Two at pins，plugs into standard AC power outlet
to provide power to your portable device.
Output voltage: 3, 4.5, 6, 7.5, 9 and 12V DC
Output current: 1200mA
Output plug: 8 detachable plugs
3.5 mm; 5 × 3.4 mm
3.5 × 1.35 mm; 5.5 × 1.5 mm;
4 × 1.7 mm; 5.5 × 2.1 mm;
5 × 2.1 mm; 5.5 × 2.5 mm;
Adapter plug tips allow a variety of devices to be powered up to
1200mA.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation of
this product is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
ICES‐003 statement
This Class B digital apparatus complies with Canadian ICES‐003.
One-year limited warranty
Visit www.dynexproducts.com for details.
© 2010 BBY Solutions, Inc. All Rights Reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective owners.
Contenu de l’emballage
• Adaptateur c.a. universel de 1 200 mA
• Guide d’installation rapide
Mise en service
1 Régler le commutateur de tension sur la tension requise par
l’appareil. Voir le guide de l’utilisateur pour déterminer la
tension requise, sinon obtenir la tension en multipliant le
nombre de piles utilisées par 1,5
(exemple : 4 piles × 1,5 = 6 V)
Remarque : La tension requise par l’appareil est également
indiquée à côté de la prise c.c. ou sur la plaque signalétique.
2 Sélectionner l’embout pour l’adaptateur correspondant à la
prise de l’appareil.
3 Insérer l’embout pour l’adaptateur dans le connecteur c.a.
de l’adaptateur.
4 Connecter l’embout pour l’adaptateur à une prise c.c. de
l’appareil.
5 Brancher l’adaptateur c.a. sur une prise secteur 110-240 V
et utiliser l’appareil normalement.
Important : Cet adaptateur est conçu pour être orienté
verticalement ou en position au sol.
6 Si l’appareil ne fonctionne pas, débrancher
immédiatement l’adaptateur c.a. et vérier de nouveau
les instructions; plus particulièrement le réglage de la
tension et de la polarité.
To Next Page
Need help?
General
