9GB
Operation: General / Radio
4. Now press buttons U or I to set the Minutes display. The Minutes setting is shown in the Display R.
5. Press the Memory button
} again. The time has now been set and is shown in Stand-By mode.
Note: If you do not perform the setting within 5 seconds the process is cancelled. If this happens, press the
Memory button
} again to repeat the process.
Setting the time using the Timer function:
1. Switch on the device as described above.
2. Press the Mode/Remain button
r once. The time is displayed.
3. Press the Memory button
} once. The Hours display starts to flash.
4. Now press buttons
U or I to set the Hours display. The Hours setting is shown in the Display R.
5. Press the Memory button
} once more and the Minutes display starts to flash.
6. Now press buttons
U or I to set the Minutes display. The Minutes setting is shown in the Display R.
7. Press the Memory button
} again. The time has now been set and is displayed in Stand-By mode.
8. Press the Mode/Remain button
r three times to quit the Timer function.
Note: If you do not perform the setting within 5 seconds the process is cancelled. If this happens, press the
Memory button
} again to repeat the process.
Setting times for switching on and off [ »TIMER« ]
Using this function you can set the times at which the device will automatically switch on and off.
You can also use this function as an alarm.
Note: If you do not perform the setting within 5 seconds the process is cancelled. If this happens, press the
Memory button
} again to repeat the process.
Setting the Switch-on time (TIMER ON):
01.Switch on the device as described above.
02.Select the desired sound source / operating mode
Y, w or i by which you wish to be woken,
(e.g. radio or CD).
03.Prepare the sound source, i.e. set the radio to the desired station or insert a CD and program the tracks
as necessary.
04.Set the required volume as described above.
05.Press the Mode/Remain button
r twice. The Display R shows TIMER ON (TIMER flashes).
06.Press the Memory button
} once. The Hours display starts to flash.
07.Now press buttons
U or I to set the Hours display. The Hours setting is shown in the Display R.
08.Press the Memory button
} once more and the Minutes display starts to flash.
09.Now press buttons
U or I to set the Minutes display. The Minutes setting is shown in the Display R.
10.Press the Memory button
} again. The Switch-on time (TIMER ON) has now been set.
If you just wish to activate the Switch-on time only, you can quit this Timer menu by pressing the
Mode/Remain button
r twice. The Display will then show TIMER ON only.
If you also wish to set a Switch-off time, continue from here to step 11 below.
Setting the Switch-off time (TIMER OFF):
11.Press the Mode/Remain button
r once. The Display R shows TIMER OFF (TIMER flashes).
12.Press the Memory button
} once. The Hours display starts to flash.
13.Now press buttons
U or I to set the Hours display. The Hours setting is shown in the Display R.
14.Press the Memory button
} once more and the Minutes display starts to flash.
15.Now press buttons
U or I to set the Minutes display. The Minutes setting is shown in the Display R.
16.Press the Memory button
} again. The Switch-off time (TIMER OFF) has now been set.
17.Press the Mode/Remain button
r once to quit the Timer menu. The Display shows TIMER ON and OFF
(in Stand-By mode as well).
Deactivating the Switch-on or -off times:
1. Press the Mode/Remain button
r twice. The Display R shows TIMER ON (TIMER flashes).
2. To deactivate the Switch-on time press the Timer button
{ – TIMER and ON flash.
3. Press the Mode/Remain button
r once. The Display R shows TIMER OFF (TIMER flashes).
4. To deactivate the Switch-off time, press the Timer button
{ – TIMER and OFF flash.
5. Press the Mode/Remain button
r once to quit the Timer menu. The Display no longer shows TIMER ON
and OFF.
The same procedure (with the appropriate changes) can be used to reactivate the Switch-on or -off times
(then the Display just flashes TIMER).
Activate/deactivate the Sleep function [ »SLEEP« ]
You can set a time of between 90 and 10 minutes, after which the device switches itself off.
· Press the Sleep button
e once. The Display R shows SLP-10 (= turns off in 10 minutes).
· Each additional press of the button will increase the Turn-off time by 10 minutes (SLP-20, SLP-30 etc. up
to SLP-90). Set the value as required.
After a few seconds the device returns to the last operating mode (e.g. returns to Radio mode).
The Display
R shows SLEEP and thus indicates that the Sleep function is activated. The device will
automatically turn off on this single occasion only and enter Stand-By mode.
· To deactivate the Sleep function, keep the Sleep button
e pressed until the Display shows SLP-00.
After a few seconds the device returns to the last operating mode (e.g. returns to Radio mode).
Operation: Radio
Attaching aerial
If you use the wire aerial for FM reception:
· The wire must be fully wound out
To Next Page
Loading...