16 – DX1208
6. SPECIFICATIONS
DX1208 SPECIFICATIONS
INPUTS / OUTPUTS
Inputs 1-8: Balanced, Euroblock terminals
Inputs 5-8: Unbalanced, RCA connectors (summed with
Inputs 5-8 on Euroblock connectors)
Inputs 9-12: S/PDIF with SRC, RCA connectors
SRC range: 32 kHz to 96 kHz
Outputs A-H: Balanced, Euroblock terminals
DXLink TX: 16 channel output bus, RJ-45 connector
DXLink RX: 16 channel input bus, RJ-45 connector
Ethernet: 1 RJ-45 connector, rear panel
USB: 1 “B” type connector, front panel
RS232: 1 RS-232C serial port on a DB9 connector,
rear panel
Logic Inputs:
6 inputs, contact closure, Euroblock terminals
Logic Outputs:
3 outputs, open-collector, Euroblock terminals
Remote: 1 remote bus with 24 VDC, RJ-25 connector
PANEL CONTROLS
Power On: Rocker switch, rear panel
Address: 10-position rotary DIP switch
PANEL INDICATORS
Input Levels: 2-segment LEDs per channel
1 Green (–40 dBFS), 1 Red (Clip)
Output Levels: 2-segment LEDs per channel
1 Green (–40 dBFS), 1 Red (Clip)
Communication: 1 Green LED, lights to indicate
communications activity
DX Link: 1 Red LED, lights when valid signal is
received at DX LINK RX port
Power: 1 Green LED
SIGNAL PROCESSING
General: 1 x 32-bit DSP
24-bit A/D and D/A converters
2M x 16 Flash
1M x 16 SDRAM
Inputs
EQ Filters: 6 per input channel
Parametric
Type: Symmetrical boost/cut
Frequency: 20 Hz to 20 kHz
Gain: ±15 dB
Bandwidth: 0.016 to 4.000 octaves
(Q = 65 to 0.25)
Low/High Shelf
Slope: 6 dB / 12 dB per octave
Frequency: 20 Hz to 20 kHz
Low/High Pass
Slope: 12 dB per octave
Frequency: 20 Hz to 20 kHz
Bypass
Bypass Filter: For each individual filter
Bypass EQ: For all EQ filters
Compressor
Threshold: +20 to –60 dB
Ratio: 1:1 to 20:1
Attack: 1 to 5000 ms
Release: 50 to 5000 ms
Gain Makeup: 0 to +40 dB, 0.5 dB steps
AGC: Enable/Disable
Bypass: For each compressor
AGC (Automatic Gain Control)
Target: +20 to –40 dB
Threshold: +20 to –60 dB, Target > Threshold
Attack: 1 to 5000 ms
Ratio: 1:1 to 20:1
Gate
Threshold: –60 to +20 dB
Attack: 1 to 200 ms
Hold: 1 to 5000 ms
Release: 1 to 5000 ms
Depth: –100 to 0 dB
Ducker
Priority: Select 1 of 5 priority levels
Depth: 0 to –60 dB, 0.5 dB steps
Outputs
EQ Filters:
10 per output channel (8 parametric, 1 HP, 1 LP)
Parametric
Type: Symmetrical boost/cut
Frequency: 20 Hz to 20 kHz
Gain: ±15 dB
Bandwidth: 0.016 to 4.000 octaves
(Q = 65 to 0.25)
Low/High Shelf
Slope: 6 dB / 12 dB per octave
Frequency: 20 Hz to 20 kHz
Low/High Pass
Slope: 12 dB per octave
Frequency: 20 Hz to 20 kHz
Crossover HP/LP
Slope: 6 dB per octave, Butterworth/Bessel
12, 18, 24 dB per octave, Butterworth
12, 18, 24 dB per octave, Bessel
12, 24 dB per octave Linkwitz-Riley
Bypass
Bypass Filter: For each individual filter
Parametric EQ Bypass:
For all EQ filters (excluding Xover filters)
Limiter
Threshold: +20 to –60 dB
Ratio: 1:1 to 20:1
Attack: 1 to 5000 ms
Release: 50 to 5000 ms
Gain Makeup: 0 to +40 dB
AGC: Enable/Disable
Bypass: For each limiter
Delay: 0 to 2000 ms
To Next Page
Loading...
Need help?
General
