ECX BARRAGE - User Manual

Questions and Answers

J
Joshua GarciaAug 17, 2025
What to do if my ECX BARRAGE does not operate?
- J
  Jacob GeorgeAug 17, 2025
  If your ECX Toy does not operate, there are several potential causes. First, the transmitter batteries might be low, so replace or recharge them. Second, the transmitter or ESC could be powered off, so power them on. Third, the vehicle battery might need replacing or recharging. Finally, the dual-rate (D/R) steering and/or throttle knobs on the transmitter might be turned to zero, so adjust them to 10.
T
Tamara HouseAug 19, 2025
Why does my ECX BARRAGE have poor range?
- N
  Natasha RamirezAug 19, 2025
  If your ECX Toy has a poor range, the transmitter batteries may be low, so replace or recharge them. Also, the receiver antenna may be damaged, so check, repair, or replace it.
S
Sarah PerkinsAug 22, 2025
What to do if my ECX BARRAGE Toy has sluggish action?
- A
  Andrew CampbellAug 22, 2025
  If your ECX Toy has sluggish action, the motor might be dirty, so check and clean it. There could also be a bind in the drivetrain, so clean or adjust it. Additionally, the vehicle battery may not be charged, so replace or recharge it.
H
heidi54Aug 26, 2025
Why the system of my ECX Toy will not connect?
- W
  Wendy DeleonAug 26, 2025
  If the system of your ECX Toy will not connect, it might be that the transmitter and receiver are too near each other; move the transmitter 3.3–9.8ft (1–3m) from the receiver. Alternatively, the transmitter and receiver could be too near large metal objects (vehicles, etc.), so move away from them. Another cause might be that the throttle trim is out of center on the transmitter, so set the throttle trim on the transmitter to zero, and turn off and on the transmitter and vehicle. Finally, the receiver might have been accidentally put in bind mode, so rebind the transmitter and receiver.
V
Victoria AllenAug 28, 2025
Why does my ECX BARRAGE Toy have a short run time?
- C
  Charles DavisAug 28, 2025
  If your ECX Toy has a short run time, the motor might be dirty. Check and clean it.
J
Joshua SheltonAug 30, 2025
What to do if the receiver of my ECX BARRAGE Toy quits responding during operation?
- S
  Stephen JordanAug 30, 2025
  If the receiver of your ECX Toy quits responding during operation, it could be due to low battery voltage, so completely recharge the battery. Alternatively, there may be loose or damaged wires or connectors between the battery and receiver, so check the wires and connection, and repair or replace them if needed.
F
Frank PerkinsSep 2, 2025
How to fix reversed controls on my ECX BARRAGE?
- V
  Victoria JohnsonSep 2, 2025
  If the controls on your ECX Toy are reversed, the ST. REV or TH. REV switch position needs to be changed.
P
Paul MillerSep 5, 2025
What to do if receiver and transmitter of my ECX BARRAGE Toy are not bound?
- P
  patrick13Sep 5, 2025
  If the receiver and transmitter of your ECX Toy are not bound, it may be that the transmitter was accidentally put in bind mode, ending the bind to the receiver, so bind the transmitter to the receiver.
R
ronaldkennedySep 8, 2025
Why is there a clicking noise in the transmission area of my ECX BARRAGE?
- J
  jeffrey30Sep 8, 2025
  If there is a clicking noise in the transmission area of your ECX Toy, it could be caused by dirt or rocks in the spur gear; remove the gear cover and inspect, replacing the gear if necessary. Another cause might be that the motor moved away from the spur gear, so reset the gear mesh.
M
Matthew HessSep 12, 2025
Why does my ECX Toy move without input?
- A
  andersonkevinSep 12, 2025
  If your ECX Toy moves forward or backward without input, the throttle trim on the transmitter might not be centered. Adjust the throttle trim to set the neutral point.

Summary

Safety and Warnings

Meaning of Special Language

Defines warning, caution, and notice terms used in the manual.

Age Recommendation

Specifies the minimum age for operating the product.

Water-Resistant Operation

General Precautions

Provides advice for operating the vehicle in wet conditions.

Wet Conditions Maintenance

Components

Quick Start Guide

Vehicle Preparations

Charging the Vehicle Battery

Instructions for charging the NiMH battery safely.

Charging Warnings

Critical warnings to follow during battery charging.

Installing the Battery

Steps to install the charged battery into the vehicle.

Transmitter Controls Overview

Battery Level Indicator

Displays the transmitter's battery status.

Throttle Trim

Adjusts the neutral point of the electronic speed control.

Steering Trim

Adjusts the steering to make the model drive straight.

Steering Wheel Operation

Controls the right and left steering of the model.

Throttle Trigger Operation

Controls power to the motor for forward or reverse.

Installing Transmitter Batteries

Binding Process

Getting Started

Operation

When You Are Finished

Motor Care

Maintenance

Setting the Gear Mesh

Procedure for adjusting the gear mesh for optimal performance.

Electronic Speed Control (ESC) Setup

Connecting and calibrating the ESC to the transmitter.

Troubleshooting Guide

Limited Warranty

Warranty and Service Contact Information

FCC Information

IC Information

EU Compliance and WEEE Disposal

Replacement Parts

Optional Parts

Parts Diagram

Front Axle Assembly

Rear Axle Assembly

ECX BARRAGE Specifications

General

Scale	1:24
Drive type	4-wheel drive (4WD)
Motor type	Brushed
Engine type	Electric engine
Product type	Crawler truck
Housing color	Gray
Built-in servo	Yes
Chassis material	Aluminum
Housing material	Metal
Channels quantity	2 channels
Construction type	Ready-to-Run (RTR)
Transmitter frequency	2.4 GHz
Battery voltage	4.8 V
Battery capacity	220 mAh
Battery technology	Nickel-Metal Hydride (NiMH)
Quantity	1