EdenPURE GEN50 - User Manual

To Next Page

GEN50 Heater

User Manual

PLEASE READ AND SAVE THESE INSTRUCTIONS

Model No.: A6035

button again after it shows “24” on the display (after about 25 seconds)

and you will see “00” which means the timer setting has been cancelled.

You can also cancel the timer function by turning the Power Button off.

9. Therapy function:

Press the Therapy button to set Therapy mode. The Therapy button design

will show on the display. Press the Therapy button again to quit this mode.

The unit will go back to the setting you had it on before you set Therapy

mode.

10. Child Lock function:

You could only set this function by pressing the Child Lock button on the

remote control for 3 seconds. There is no Child Lock button on the unit.

The Child Lock indicator on the display will turn on after you activate

this function and unit will keep the settings that were on before you set

Child Lock function. To turn the Child Lock function off, press the Child

Lock button again on the remote control. You cannot change any settings

without unlocking the Child Lock function using the remote control.

Note: The Child Lock function will be stopped automatically if the power

to the unit is turned off at any time.

11. Beep Button:

Press the Beep button on the remote control to turn on / off the beep that

occurs when the unit is turned on and off.

12. Display Off Function:

Press the Display Off button on the remote control and the display light

will be dimmed to 50% off. Press the button again and the display light

will be 100% turned off except for the power light.

13. Special Instruction:

Under Quiet mode, all the indicators will turn off except the Power Light

after 10 seconds.

Storage & Maintenance

1. Turn the power switch off and unplug the power cord before you clean the

unit.

2. Use a wet soft cloth to clean the surface of the unit.

3. Remove the ﬁlter cover and use water to clean the ﬁlter, making sure to air

dry the ﬁlter completely before you place the ﬁlter back into the unit.

4. Pack the unit into the box and store it in a dry place.

5. Do not use water to clean the unit.

6. Do not use any detergent or chemicals to clean the unit. They may damage

the unit or cause the color of the unit to change.

EdenPURE

Main Page

Need help?

Do you have a question about the EdenPURE GEN50 and is the answer not in the manual?

The EdenPURE GEN50 Heater, Model No.: A6035, is a portable electric heater designed for indoor use, providing supplemental heat and offering various features for user comfort and convenience. It operates on a standard 120 V, 60 Hz power supply and has a rated power of 1500 W.

Function Description:

The primary function of the EdenPURE GEN50 Heater is to provide warmth to an indoor space. It utilizes a heating element and a fan to circulate warm air. The heater offers multiple heating modes, including Quiet (Q), Low Heat (L), Medium Heat (M), High Heat (H), and Turbo Heat (T), allowing users to select the desired level of warmth and fan speed. It also incorporates a "Therapy" mode, though its specific function beyond setting a particular heating profile is not detailed. The device features a thermostat that allows users to set a target temperature between 60-90 degrees F, with a default setting of 90 degrees F. The fan continues to run for a few seconds after the unit is turned off to dispense accumulated heat, preventing overheating.

Important Technical Specifications:

Product Name: GEN50 Heater
Model No.: A6035
Rated Voltage: 120 V
Rated Power: 1500 W
Frequency: 60 Hz
Temperature Range: 60-90 degrees F (default 90 degrees F)
Fan Speed Levels: Up to 5 levels, depending on the heating mode (High Mode: Level 3, 4, 5; Medium Mode: Level 2, 3, 4, 5; Low Mode: Level 1, 2, 3, 4, 5). Fan speed cannot be changed in Turbo and Quiet modes.
Timer Function: 1-24 hours, with a "00" display indicating cancellation.

Usage Features:

The EdenPURE GEN50 Heater is designed for user-friendly operation, primarily through a control panel on the unit and a remote control.

Power On/Off: The unit has a power switch at the rear. Once turned on, it enters stand-by mode. The power button on the unit or remote activates the heater. Pressing it again turns the unit off.
Heating Modes: Users can cycle through Quiet, Low Heat, Medium Heat, High Heat, and Turbo Heat modes using the control panel or remote.
Temperature Setting: The desired target temperature can be set between 60-90 degrees F using the Temperature + or - buttons. The default temperature is 90 degrees F.
Fan Speed Adjustment: The fan speed can be adjusted using the Fan Speed Indicator button, offering up to 5 levels depending on the selected heating mode.
Timer Function: A timer allows users to set the heater to operate for 1 to 24 hours. The timer can be canceled by setting it to "00" or by turning off the power.
Therapy Function: A dedicated "Therapy" button activates and deactivates a specific heating mode.
Child Lock Function: This feature, accessible only via the remote control (by pressing the Child Lock button for 3 seconds), locks the current settings to prevent accidental changes. It is automatically disabled if the power to the unit is turned off.
Beep Button: The remote control includes a button to turn the audible beep on or off when the unit is operated.
Display Off Function: The display light can be dimmed to 50% or turned off completely (except for the power light) using the Display Off button on the remote. In Quiet mode, all indicators except the Power Light turn off after 10 seconds.
Placement Recommendations: For optimal performance, the heater should be placed in an area with a high rate of air filtration and movement. It should be positioned away from walls and other obstructions to allow for efficient heating and air circulation. Combustible materials should be kept at least 3 ft away from the front, sides, and rear of the heater.
Safety Precautions:
- Do not use the heater outdoors or on construction sites.
- Avoid using it in bathrooms, laundry areas, or areas with standing water.
- Do not run the power cord under carpeting or cover it with rugs.
- Do not plug the heater into power strips, surge protectors, multiple outlet adapters, grounding adapters, or outlet-type air fresheners.
- Do not insert foreign objects into ventilation or exhaust openings.
- Do not block air intakes or exhaust, especially on soft surfaces like beds.
- Do not block the front or rear of the heater.
- Unplug the heater when not in use.
- Exercise extreme caution when used near children or when left unattended.
- If the heater malfunctions or is damaged, contact a service center for repair.
- Do not attempt to repair the heater yourself; unauthorized repairs will void the warranty and pose a risk of fire, electric shock, and injury.
- The heater grill becomes hot during use; avoid direct skin contact.

Maintenance Features:

Regular maintenance is crucial for the longevity and safe operation of the EdenPURE GEN50 Heater.

Cleaning:
- Always turn off the power switch and unplug the unit before cleaning.
- Use a wet soft cloth to clean the exterior surface of the unit.
- The filter cover can be removed, and the filter cleaned with water. Ensure the filter is completely air-dried before reinserting it into the unit.
- Do not use water to clean the main unit.
- Avoid using detergents or chemicals, as they may damage the unit or alter its color.
Storage:
- After cleaning, pack the unit back into its original box and store it in a dry place.
- It is recommended to keep the original packaging for off-season storage and transport needs.
Filter Maintenance: The manual emphasizes that any required service other than filter maintenance or replacement should only be performed by an authorized service representative.