2. Functional operation
Note:
•Images are for illustrative purposes only and may dier from the actual product.
•For the need of technical improvement and system upgrade, information and
specications contained herein may be slightly dierent from actual product. If any
dierence is found, the actual product prevails.
Play/pause (Bluetooth mode)
Next track (Bluetooth mode)
Previous track (Bluetooth mode)
Mute/mute o (AUX/OPT mode)
Control
Active speakerPassive speaker Remote control
Cleaning cloth
● Side view of active speaker
Disconnect Bluetooth
● Rear view of active speaker
Power adapter & power cable
Quick start
guide
Important safety
instructions
3.5mm to RCA audio cable
3.5mm to 3.5mm audio cable
Speaker connecting cable
Fiber optic audio cable
OPT
AUX
Multimedia Speaker
e25HD
Manual
x1
3s
Volume up
Volume down
Mode Indicator
Green: AUX mode
Red: OPT mode
Blue: Bluetooth mode
Power on/o
Press and hold: power on/o
Press: switch input mode
(Bluetooth/AUX/OPT)
Audio input port
Power adapter port
Connect to passive speaker
EN
1. What’s in the box?
● Rear view of passive speaker
Connect to active speaker
OPT
AUX
OPT
AUX
4. Connection
5. Operating instructions
● Bluetooth input
Note:
•Pin code for connection is "0000" if needed.
•To enjoy all Bluetooth functions of this product, make sure that your audio source
device suppos A2DP and AVRCP proles.
•If no device is connected in 30 minutes, the speaker will switch to Bluetooth hidden
mode. In this mode, (1) new devices cannot nd the speaker, but (2) for a device
that exists in the pairing record of this speaker, you can select "EDIFIER e25HD"
from its Bluetooth device list to reconnect. To exit from Bluetooth hidden mode,
press the " " button on the speaker or the " " button on the remote control.
•To disconnect from the current Bluetooth device, press and hold the " " button
on the remote control for 1.5 seconds, or simultaneously tap and hold the buttons
of " ", " ", and " " on the active speaker for 3 seconds.
● AUX input
● OPT input
6. Specications
7. Troubleshooting
3. Remote control
Batte replacement
1. Slide the switch along the slot to the end and simultaneously rotate the batte
compament lid counterclockwise until the point indicator aligns with the " " icon.
2. Remove the batte compament and inse a new batte into the batte
compament with its positive electrode outwards.
3. Put back the batte compament lid and rotate it clockwise until the point
indicator aligns with the " " icon.
Switch to Bluetooth mode.
Select "EDIFIER e25HD" in your device setting to connect.
The indicator light will blink blue rapidly and then remain solid blue if successful.
Solid green
Play audio on the connected device.
Press the " " button on the active speaker or the " " button
on the remote control.
or
Switch to AUX mode.
Press the " " button on the active speaker or the "AUX" button
on the remote control.
or
Connect the speakers to your audio device using the audio cable.
Solid red
Play audio on the connected device
Switch to OPT mode
Press the " " button on the active speaker or the "OPT" button
on the remote control.
or
Connect the speakers to your audio device using the ber optic audio cable.
Total output power: R/L(Treble): 15W+15W, R/L(Mid-Bass): 22W+22W
Frequency response: 50Hz-40kHz
Input: 20V 2.75A
Declaration for EU
Frequency Band: 2.402GHz ~ 2.480GHz
RF Power output: ≤13 dBm (EIRP)
There is no restriction of use.
+
CR2025
or
AUX
OPTAUX
OPT
*
Power input: 100-240V~ 50/60Hz
* This plug type is meant for illustration purpose only.
Cannot connect to your Bluetooth device
•
Make sure that the distance between this product and your Bluetooth device
is less than 10 meters and there are no obstacles between them.
•
Make sure that no device is connected to this product via Bluetooth.
•
Make sure that this product is in Bluetooth pairing mode. If not, manually
switch it to this mode.
•
Resta this product, enable Bluetooth function on your Bluetooth device,
and then t again.
•
Reset this product to facto settings and t again.
No power
•
Make sure that the power cable is properly connected.
•
Make sure that the power supply is not disconnected.
No sound
•
Make sure that this product and your device is properly connected.
•
Make sure that the correct audio input source is selected.
•
Make sure that the playback is not paused.
•
Make sure that this product and your device are not muted.
•
Increase the volume of this product and your device.
Noise coming from speakers
•
EDIFIER speakers generate little noise, while the background noise of some
audio devices are too high. Please unplug audio cables and turn the volume
up. If no sound can be heard at 1 meter away from the speaker, there is no
problem with this product.
To learn more about EDIFIER, please visit www.edier.com
For EDIFIER warranty queries, please visit the relevant count page on
www.edier.com and review the section titled Warranty Terms.
USA and Canada: seice@edier.ca
South America: Please visit www.edier.com (English) or
www.edierla.com (Spanish/Pouguese) for local contact information.
Bluetooth
Settings
EDIFIER e25HD
DEVICES
Bluetooth
2:12
Power on/o
Volume up
Previous track (Bluetooth mode)
Play/pause (Bluetooth mode)
Mute/mute o (AUX/OPT mode)
Next track
(Bluetooth mode)
Volume down
Bluetooth mode
Press: Bluetooth mode
Press and hold:
disconnect Bluetooth
AUX mode
OPT mode
OPT
AUX
Solid blue
Note:
The speaker detects the plug-in or plug-out of a ber optic audio cable.
•If a ber optic audio cable is connected, the speaker will switch to OPT mode
automatically.
•If the ber optic audio cable is plugged out, the speaker will switch to
Bluetooth mode automatically.
Note:
The speaker detects the plug-in or plug-out of an AUX audio cable.
•If an AUX audio cable is connected, the speaker will switch to AUX mode
automatically.
•If the AUX audio cable is plugged out, the speaker will switch to Bluetooth mode
automatically.
To Next Page
Need help?
General
