What to do if Efco Trimmer engine will not start or runs only briefly?
If your Efco Trimmer engine won't start or only runs for a few seconds, here's what you can do: 1. Check for a spark at the spark plug tip. If there's no spark, try again with a new spark plug (CMR7H). 2. If the engine is flooded, follow the procedure on page 28. If it still doesn't start, repeat the procedure with a new spark plug.
Why Efco Trimmer engine does not reach full speed and emits excessive smoke?
There are several reasons why your Efco Trimmer engine may not reach full speed or might emit excessive smoke: 1. Check the fuel mixture. Use fresh fuel and the correct 2-cycle oil mix. 2. The air filter might be dirty. Clean it following the instructions in the Maintenance-Air Filter Section. 3. The carburetor may require adjustment. Contact a Servicing Dealer for carburetor adjustment.
What to do if Efco Trimmer engine starts but won't accelerate properly?
If your Efco Trimmer engine starts but doesn't accelerate properly or run well at high speed, the carburetor likely needs adjustment. Contact a Servicing Dealer to adjust the carburetor.
What to do if Efco Trimmer engine starts, runs and accelerates but will not idle?
If your Efco Trimmer engine starts, runs, and accelerates but won't idle, turn the idle speed screw “T” (Fig. 21) clockwise to increase the idle speed. See Operation-Carburetor Adjustment.
Why Efco Trimmer cutting attachment is not rotating?
If the Efco Trimmer engine starts and runs, but the cutting attachment isn't rotating: 1. The clutch, bevel drive, or transmission shaft might be damaged. If replacement is needed, contact a Servicing Dealer. 2. The attachment might be incorrectly installed. Mount the attachment correctly, referring to the instructions in the ASSEMBLY section.
Why is my Efco DS 2400 S Brush Cutter engine overheating?
If your Efco Brush Cutter engine is overheating, it could be due to several reasons: * The carburetor mixture might be too lean: Set the carburetor. * There might be an air leak in the engine or fuel system: Find and eliminate the leak. * The oil-fuel ratio could be incorrect: Replace the fuel with a fresh mixture. * The fan, starter housing, or cylinder fins might be dirty or damaged: Clean or replace the affected parts. * There could be carbon deposits on the piston: Eliminate the deposits.
Why is the engine performance of my Efco DS 2400 S not stable?
If your Efco Brush Cutter engine performance is unstable, it could be due to: * A dirty air filter: Clean or replace it. * A loose or damaged sparkplug: Tighten or replace it. * Water in the fuel: Clean the carburetor and replace the fuel. * Low engine compression: Perform a compression test. * A faulty carburetor or diaphragm: Check and replace if necessary.
What to do if my Efco DS 2400 S tool does not work correctly or does not rotate?
If your Efco Brush Cutter tool isn't working correctly or rotating, inspect these components: 1. Check the bevel gear, transmission shaft, and clutch drum for damage. 2. Replace the shaft transmission if the shaft drive teeth are worn or damaged. 3. Replace the clutch if it's worn. 4. Ensure the transmission tube is correctly fitted on the clutch drum by unscrewing the handle and verifying the transmission shaft's position.
How to fix a noisy or vibrating Efco DS 2400 S?
If your Efco Brush Cutter is noisy or vibrating, it could be due to: * A bent shaft: Exchange the complete shaft. * A probable seizure of the bushing in the shaft: Exchange the complete shaft of bushings.
General| Engine Type | 2-Stroke |
|---|---|
| Power Output | 0.8 kW |
| Power | 1.1 HP |
| Weight | 4.5 kg |
| Shaft Type | Straight |
| Cutting System | Tap & Go Head |
| Fuel Tank Capacity | 0.4 L |
To Next Page
