EasyManuals Logo

EINHELL ARCURRA User Manual

EINHELL ARCURRA
Go to English
138 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
GB
- 18 -
4. Technical data
Cutter rail length ..................................... 620 mm
Cutting length ......................................... 550 mm
Tooth spacing ........................................... 18 mm
Cuts/min. ..................................................... 2400
Sound pressure level L
pA
...................... 81 dB (A)
Sound power level L
WA
.......................... 91 dB (A)
Uncertainty K
pA
/ K
WA
.............................. 3 dB (A)
Vibrations a
h
............................................3.4 m/s
2
Uncertainty K ..........................................1.5 m/s
2
Caution
The equipment is supplied without batteries and
without a charger. It must only be used with the li-
thium-ion batteries in the Power-X-Change series.
The lithium-ion batteries of the Power-X-Change
series must only be charged only with the Power-
X charger.
The noise generated by the unit can exceed 85
dB (A). The operator will require noise protection
measures if this is the case. The noise emitted by
the hedge trimmer was measured in accordance
with EN 60745-1. The vibration emission level at
the handle was determined in compliance with
EN 60745-1.
The speci ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the speci ed value
in exceptional circumstances.
The speci ed vibration value can be used to
compare the equipment with other electric power
tools.
The speci ed vibration value can be used for initi-
al assessment of a harmful e ect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
5. Before starting the equipment
The equipment is supplied without batteries
and without a charger.
Assembly of the steady grip
Push on the steady grip (Fig. 2 / item 3) in the di-
rection of the arrow as shown in Fig. 4a.
Make sure that the electrical contacts are
connected correctly.
Then tighten the screws (Fig. 4b / item 5).
Fitting the cuttings collector (Fig. 5a-5c)
For horizontal cutting we recommend that you
install the cuttings collector. This enables you to
remove the cuttings easily and keep the top of
the hedge clear (Fig. 5a/5b). Position the cuttings
collector (6) on the cutter rail (Fig. 5c). Then slide
the cuttings collector toward the tip of the cutter
rail to clamp it rmly under the retaining pin (Fig.
5c / item A).
Installing the battery (Fig. 4c)
Press the push/lock button of the battery pack as
shown in Fig. 4c and slide the battery pack into
the mount provided. Make sure that the push/lock
button engages properly. To remove the battery
pack, follow the steps in reverse order.
Charging the battery (Fig. 6)
1. Take the battery pack out of the equipment.
Press the push/lock button to do this.
2. Check that your mains voltage matches the
voltage speci ed on the rating plate of the
battery charger. Insert the power plug of the
charger into the socket outlet. The green LED
will then begin to ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator“
there is a table with an explanation of the LED
display on the charger.
The battery pack can heat up slightly during char-
ging. This is normal.
If the battery pack fails to charge, please check:
whether there is a voltage at the mains power
socket;
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, please send
the charging unit
and the battery pack
to our customer service center.
Anl_ARCURRA_SPK9.indb 18Anl_ARCURRA_SPK9.indb 18 01.10.2018 07:55:2601.10.2018 07:55:26

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the EINHELL ARCURRA and is the answer not in the manual?

EINHELL ARCURRA Specifications

General IconGeneral
Blade size620 mm
Blade typeDouble blade
Cutting length55 mm
Blade tooth spacing18 mm
Engine power2400 W
Power sourceBattery
AC input voltage18 V
Weight and Dimensions IconWeight and Dimensions
Depth1030 mm
Width200 mm
Height145 mm
Weight2850 g
Package weight4290 g

Related product manuals