GB
- 37 -
contact our customer service or the point of
sale at which the equipment was purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Special safety instructions
•
Hold the power tool by insulated gripping
surfaces only, because the cutter may
contact its own cord. Cutting a „live“ wire
may make exposed metal parts of the power
tool „live“ and could give the operator an elec-
tric shock.
•
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by your
hand or against the body leaves it unstable
and may lead to loss of control.
•
Before you put the electric router into opera-
tion, check to ensure that the routing tool is
firmly seated and runs smoothly!
•
Never use a low quality or damaged routing
cutter.
•
Only use routing cutters whose shaft diame-
ter complies with the specifications in the
instructions.
•
The maximum speed specified for the routing
cutters is not allowed to be exceeded.
•
Never cut over metal parts, screws, nails etc.
•
To avoid damage to the router, make sure
there are no foreign objects stuck to the work-
piece.
•
Always guide the router with both hands.
•
Let the router reach full speed before plun-
ging the routing cutter into the workpiece.
•
If the router becomes clogged with work
debris, switch it off. Let the router run to a
complete stop. Remove the debris with a long
stick and not with your fingers.
•
Let the router run to a complete stop before
removing the workpiece or setting down the
tool.
•
Always cut on a counter-rotating basis.
•
Watch out for the reaction torque of the tool,
especially if the router becomes jammed.
•
When you have finished your work, slide the
tool back to starting position.
•
Use only properly sharpened routing cutters.
•
Clamp the routing cutter by friction-locking.
•
For deep cuts, carry out the work in several
steps according to the material in question.
•
Use only cutters with a shaft diameter which
matches the integrated clamp.
•
Use only cutters which are suitable for the
speed of the electric tool.
Do not lose these safety instructions.
2. Layout and items supplied
2.1 Layout (Fig. 1+2)
1. Cordless routing unit
2. Unlock button
3. On/Off switch
4. Speed control
5. Spindle lock
6. Clamp nut
7. Handles
8. Fastening screw for depth adjuster
9. Height adjuster
10. Fastening screw for routing guide
11. Extractor adapter
12. Countersunk head screw for extractor adap-
ter
13. Open-ended wrench
14. Copy sleeve
15. Clamp ¼“
16. Routing guide
17. Compass point
18. Parallel stop
19. Palm router insert
20. LED lamp
21. Scale
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Anl_TP-ET_18_Li_BL_SPK8.indb 37Anl_TP-ET_18_Li_BL_SPK8.indb 37 06.03.2024 08:51:0806.03.2024 08:51:08
To Next Page
Loading...
