Name: ELCOS QPE-C
Brand: ELCOS
Rating: 4 (1 reviews)

To Next Page

ENG

INSTALLATION, USE and MAINTENANCE Manual

QPE-C Elcos Polyvalent Panel

Command and control solutions

QPE-C-O-SC / QPE-C-O-CC / QPE-C-V

www.elcos.net

E-All. 47 proc.04 rev.03 del 10-01-2013

Default Chapter2
- Table of Contents2
User Manual5
Introduction5
Aim5
Operating Basics5
- How the Qpe-C-V Panel Works with the Genset5
- Qpe-C-Vadjustable Operating Modes7
- How the Qpe-C-O Panel Works with the Genset8
- Qpe-C-Occ Operating Mode9
- Qpe-C-Osc Operating Mode9
Examination of "Mc4 on Qpe-C Panel" Module11
Funtional Description of Panel Components11
- Description of Keyed Selector Function11
- Description of Single Buttons and Warning Light Functions12
- Description of Different Measurements and Reporting14
Commands and Functioning in the Three Modes21
- Setup of Operating Modes21
- Mode 1 Manual21
- Mode 2 Automatic22
- Mode 3 Mod - Bus22
Setup Language23
Other Functions23
- Emergency Stop23
- Locked Genset24
- Remote Testing - Ejp24
- Master Start24
- Maintenance Request24
- Teleprocessing24
- Scheduled Start-Ups24
- Programmable Relay Genset Conditions25
- Differential or Earth Failure Protection25
- Electronic Overload (51) and Short-Circuits (50) Protection25
- Reverse Power Protection (32)26
- Alarms History26
- Fuel Pump Command27
- Programming the Card through Usb Port27
- Password Locked & Unlocking Procedure27
- Led Test27
- Automatic Battery Charger Function27
- Fuel Theft Function28
- Dummy Load Function28
- Load Shedding Function28
- Double Starter Function28
- Fuel Monitoring Function28
- Battery Charged Test Function29
- Low R.p.M. Operating Function29
- Service Phone Number Signalling29
- Variable Speed Function29
Interpretation of Alarms and Controls30
- What to Do in Case of Genset Failure30
- Alarms and States Summary34
- Electrical Maintenance35
- Mccb Reset35
- Mechanical Maintenance35
- Periodic Checks35
2 Installation Manual36
Constructive Description of Qpe-C Panel36
- External Composition Qpe-C-V Panel36
- Qpe-C-Occ Panel Composition (with Switching on Board)37
- Qpe-C-Sc Panel Composition (Without Switching)38
Constructive Description of Mc4 Card40
- Constructive Characteristics Mc4 Card40
- Technical Characteristics Summary41
Electrical Connections between Mc4 Motherboard and the Generating Set42
- J1 Connector Power Supply Systems C.C and Command Relay42
- J2 Connector Can-Bus Engine Connection43
- J3 Connector Engine Protection Digital Inputs43
- J4 Connector Analogical Inputs to Measure Engine Parameters45
- J5 Connector Toroid Connection Differential Protection48
- J7 Connector Mccb Opening Coil50
- J8 Connector Line Generator Input50
- J9 Connector Fuel Pump Supply51
- J10 Connector Floating Overflow51
Electric Wiring Mc4 Motherboard with External Users52
- J11 Connector Data Trasmission in Mod-Bus52
- J12 Connector Remote Controls52
- J13 Connector Remote Signals52
- J14 Connector Programmable Reporting Relay53
- J15 Connector Management of Mains-Genset Remote Switching53
- J16 Connector Battery Charger Connection55
- J17 Connector Mains Presence Sensor Connection56
Setup57
- Setup Mode Activation57
- Clock Menu57
- Differential Menu58
- Times Menu59
- Thresholds Menu59
- Settings Menu61
- Calibration Menu64
- Modem Menu65
- Can-Bus Menu66
- Mod-Bus Menu67
- Usb Menu67
- Card Menu68
- Special Functions Menu70
Technical Notes of Mc4 Card73
- Engine Running Detection73
- Operating When the Microprecessor Is Blocked73
- Password Lock and Release73
- Password Release74
- Firmware Software Display74
Accessories Combinable with Qpe-C Panel76
- Modem for Remote Management of Generating Set76
- Remote Display78
- Aux16 Auxiliary 16-Relay Module81
- Radio Channel85
- Remote Management Software Mc4 Monitoring85
- Mod-Bus Protocol86
Electric Connection Diagram Qpe-C90
- Engine Connector Qpe-C-V and Qpe-C-O90
- Alternator Connector for Qpe-C-V90
- Fuel Topping System Connector Qpe-C-V and Qpe-C-O91
- Wiring Diagram for Qpe-C-V92
Installation95
- Protection Degree95
- Ground Connections (Pe)95
- Power Connections95
- Battery Connection96
- Summary of Control Probes Mounted on the Engine96
- Dielectric Strength Test97
Service Procedures98
- First Start-Up Procedure98
- Procedure for Replacing the Battery98
- Procedure for Replacing Mc4 Card98
3 Maintenance Manual99
- Routine Maintenance99
- Electrical and Mechanical Maintenance99
- Test and Alarms Simulation99
- Engine Protections99
- Generator Protection99
- Overload Protection99
- Troubleshooting100
Warranty101

Questions and Answers:

Need help?

Do you have a question about the ELCOS QPE-C and is the answer not in the manual?

ELCOS QPE-C Specifications

General

Brand	ELCOS
Model	QPE-C
Category	Control Panel
Language	English

Related product manuals

ELCOS QPE-C User Manual

Table of Contents

Questions and Answers:

ELCOS QPE-C Specifications

Related product manuals