This document is an installation manual for the Electrolux Professional WH6-14LAG Clarus Vibe washer extractor, Type W3.... It provides detailed instructions for setting up, connecting, and performing initial checks of the appliance, along with safety precautions, technical data, and disposal information.
Function Description
The Electrolux Professional WH6-14LAG Clarus Vibe is a commercial and industrial washer extractor designed for water-wash of textiles. It is intended for use in various commercial settings, including staff kitchen areas, farmhouses, hotels, motels, residential environments, bed and breakfast establishments, and communal laundrettes. The machine is equipped with features for external dosing systems, steam connection, and can be converted for different electrical power configurations.
Important Technical Specifications
General Data:
- Weight, net: 263 kg
- Drum volume: 130 litres
- Drum diameter: 650 mm
- Drum speed during wash: 44 rpm
- Drum speed during extraction: 1113 rpm
- G-factor, max.: 450
- Frequency of the dynamic force: 18.6 Hz
- Floor load at max extraction: 3.1 ± 0.5 KN
- Maximum mass of dry cloth: 14.5 kg
Heating:
- Electricity: 13 kW
- Steam: X (indicates availability)
- Hot water: X (indicates availability)
Sound Levels (measured according to ISO 60704):
- A-weighted emission sound pressure level at working stations (Wash): <70 dB(A)
- A-weighted emission sound pressure level at working stations (Extraction): <70 dB(A)
- Sound power/pressure level at extraction: 78/62 dB(A)
- Sound power/pressure level at wash: 63/48 dB(A)
Water Connections:
- Water valves (DN/BSP): 20 / 3/4"
- Minimum inlet water pressure: 50 kPa
- Recommended water pressure: 200-600 kPa
- Continuous operating pressure: 50-800 kPa
- Maximum inlet water pressure: 1000 kPa
- Capacity at 300 kPa: 20 l/min
- Inlet temperature for cold water: Must not be higher than 25°C (for Lagoon Advanced Care programs, pre-heating to 25°C is required for cold water valves).
Drain Connection:
- Drain valve Ø outer: 75 mm
- Draining capacity: 170 l/min
Steam Connection:
- Steam valve connection (DN/BSP): 15 / 1/2"
- Recommended steam pressure: 300-600 kPa
- Functioning limits for steam valve: 50-800 kPa
- Note: A steam heated machine is only intended to use clean steam.
Electrical Connections:
The machine can be configured for various electrical supplies:
- Electric heated:
- 220-240V 1/1N~ (50/60 Hz): Heating power 4.8/13.0 kW, Total power 5.2/13.4 kW, Recommended fuse 25/63 A
- 220-240V 3~ (50/60 Hz): Heating power 4.8/13.0 kW, Total power 5.2/13.4 kW, Recommended fuse 16/35 A
- 380-415V 3N/3~ (50/60 Hz): Heating power 4.8/13.0 kW, Total power 5.2/13.4 kW, Recommended fuse 10/20 A
- 440V 3~ (50/60 Hz): Heating power 13.0 kW, Total power 13.4 kW, Recommended fuse 20 A
- 480V 3~ (60 Hz): Heating power 13.0 kW, Total power 13.4 kW, Recommended fuse 20 A
- Non heated/Steam heated:
- 208-240V 1/1N~ (50/60 Hz): Total power 1.2 kW, Recommended fuse 10 A
- 380-480V 1~ (50/60 Hz): Total power 1.2 kW, Recommended fuse 10 A
- Conversion: This model can be converted from 380-415V 3N AC to 220-240V 1N AC with reduced power.
Dimensions (mm):
- A: 910, B: 820, C: 1345, D1: 440, D2: 515, E: 1310, F: 1050, G: 80
- H: 1245, I: 375, J: 295, K: 1225, L: 1125, M: 360, N: 105, O: 305
- P: 295, Q: 210
Usage Features
- Commercial Use Only: The machine is designed exclusively for commercial and industrial applications.
- Water-Wash Only: Intended solely for water-wash of textiles; dry cleaning agents must not be used.
- External Dosing Systems: Prepared for connection to Jetsave and Dosave dosing systems, with specific instructions for tube connections (17 mm for dosing systems, 6 mm for dosing systems, and a flush manifold connection). External dosing equipment must operate on pump pressure, not network pressure.
- Water Hardness and Dosage: Provides tables for adjusting detergent and conditioner dosage based on water hardness (in °D, °F, and °E) and specific programs (e.g., Wool High/Medium, Synthetics-Mix Medium/Low, Gentle 40). A water hardness kit (Part No. 0S0586) is available.
- Clarus Vibe Control: The "Clarus Vibe" designation indicates an advanced control system, likely offering programmable wash cycles and user-friendly interface.
- Public Area Installation: If installed in a public area, specific segments must be selected during the initial power-up setup, such as "Apartment Auto Dosing," "Laundromat/Launderette," or "Camping/Marina."
Maintenance Features
- Authorized Service: Servicing must be carried out only by authorized personnel using genuine spare parts, accessories, and consumables.
- Easy Access for Service: The machine should be positioned with sufficient room for working, both for the user and service personnel, with minimum distances to walls and other machines (25 mm to a wall, 500 mm to another machine) to ensure easy access for maintenance.
- Water Shut-off Valves and Filters: All water intake connections should be fitted with manual shut-off valves and filters to facilitate installation and servicing.
- New Water Hoses: The machine must be connected with new water hoses; re-used hoses are not permitted.
- Electrical Safety: A multi-pole switch must be mounted prior to the machine to facilitate installation and service operations. For EMC compliance, a ferrite (enclosed with the machine) must be used with the protective earth (PE) wire wrapped around it.
- Transport Supports: Removable transport supports are used for secure transportation and should be saved if the machine needs to be moved in the future.
- Function Check: After installation, a comprehensive function check is required, including verifying drum rotation, checking for leaks in water supply/drain connections, ensuring water passes through the detergent container, and confirming the door lock functions during a program.
- Disposal Information: Detailed instructions for the differentiated disposal of machine parts (metals, oils, greases, plastic, rubber) and packaging materials (wrapping film, corner protection, cardboard, pallet, screws, nuts, plastic bags) are provided, emphasizing compliance with local regulations and environmental responsibility. The manual also states that any markings, the manual itself, and other documents should be destroyed when scrapping the machine.
Need help?
General
To Next Page