9
GB
KOR
CHS
CHT
THA
IND
VIE
Cleaning / 청소 / 清洁
Cleaning the brush roll with the BRUSHROLLCLEAN™ function* / BRUSHROLLCLEAN™ 기능을 활용하여 브러쉬 롤 청소하기* /
使用 BRUSHROLLCLEAN™ 功能
*
清洁刷辊
*
The BRUSHROLLCLEAN™ function is equipped with
an overheating protection. It will deactivate the
brush roll if the BRUSHROLLCLEAN™ function has
been activated for more than 30 sec (constant or
interrupted) within one discharging period.
When the button is released, the brush is rotating and the nozzle front lights are on again. You can continue to
use the Ergorapido for vacuuming as usual. The BRUSHROLLCLEAN™ function will remain disabled. To reset, the
Ergorapido must be charged continuously for at least 10 minutes in the charging stand.
BRUSHROLLCLEAN™ 에는 과열 방지
기능이 있습니다 만약 한 방전 기간 동안
BRUSHROLLCLEAN™ 기능이 30초 이상 (지속적
또는 간헐적으로) 작동하는 경우 자동으로 브러쉬
작동이 중지됩니다
버튼이 해제되면, 브러쉬는 다시 회전하고 노즐 전면등은 다시 켜지게 됩니다 그 뒤 Ergorapido
제품을 다시 평상시처럼 진공 청소기로 사용할 수 있습니다 BRUSHROLLCLEAN™ 기능은 계속 꺼진 상태를
유지합니다 재설정하려면, Ergorapido를 반드시 10분 이상 지속적으로 충전대에서 충전해야 합니다
安全的.BRUSHROLLCLEAN™.功能配有过热保护措
施。在一个放电期间,如果.BRUSHROLLCLEAN™..
功能的激活时间超过.30.秒(连续或累计),刷辊
将停止工作。
2. Ergorapido:
If - while holding the BRUSHROLLCLEAN™ button
pressed down – the brush stops rotating and
the nozzle front lights switch o, release the
BRUSHROLLCLEAN™ button.
1. Ergorapido plus:
If - while holding the BRUSHROLLCLEAN™ button
pressed down – the brush stops rotating, the
nozzle front lights -switch o and the battery
indicator light blinks red and blue, release the
BRUSHROLLCLEAN™ button.
2.
Ergorapido:
BRUSHROLLCLEAN™ 버튼을 누르는 동안
브러쉬가 회전을 멈추거나 노즐 전면등이
꺼지는 경우, BRUSHROLLCLEAN™ 버튼을
해제합니다
1.
Ergorapido plus:
BRUSHROLLCLEAN™ 버튼을 누르는 동안
브러쉬가 회전을 멈추거나, 노즐 전면등이
꺼지는 경우, BRUSHROLLCLEAN™ 버튼을
해제합니다
2. Ergorapido:
. 如果按下.BRUSHROLLCLEAN™ 按钮时刷头停
止转动,并且吸头正面指示灯熄灭,请松开
BRUSHROLLCLEAN™.按钮。
1. Ergorapido 增强版:
. 如果按下.BRUSHROLLCLEAN™ 按钮时刷头停止转
动,吸头正面指示灯熄灭,并且电池指示灯闪烁
红、蓝两色,请松开.BRUSHROLLCLEAN™..
按钮。
松开按钮时,刷头和吸头正面指示灯将再次旋转和点亮。您可以继续正常使用.Ergorapido.进行清洁。此
时.BRUSHROLLCLEAN™.功能将保持禁用状态。要重置此功能,必须将.Ergorapido.置于充电基座上持续充电
至少.10.分钟。
* ZB2932, ZB2933, ZB2934, ZB2935, ZB2941, ZB2942, ZB2943