Elektra Beckum 4 DN User Manual

PK 255
D
Betriebsanleitung
Systemkreissäge
G
Operating Instruction
System circular saw
F
Instructions d'utilisation
Scie circuaire à système
25
20
15
10
5
0
30
35

Elektra Beckum 4 DN Specifications

General

Brand	Elektra Beckum
Model	4 DN
Category	Saw
Language	English

Summary

Warranty Information

Warranty Procedures by Country

Instructions for warranty claims specific to different countries.

Scope of Delivery

Saw Components and Controls

Safety Information

Specified Conditions of Use

Defines the intended application and restrictions for the saw.

General Safety Information

Outlines basic safety requirements for power tool operation.

Symbols and Safety Devices

Symbols Shown on the Machine

Explains warning symbols and their meanings for safe operation.

Safety Devices

Details critical safety components like riving knife, blade guard, push stick.

Operating Controls

On/Off Switch with Emergency Stop

How to operate the main power switch and emergency stop function.

Ratchet Lock Lever

Mechanism for locking the blade tilt angle during operation.

Handwheel for Blade Tilt Setting

Adjusting the angle of the saw blade for bevel cuts.

Handwheel for Setting Depth of Cut

Adjusting the vertical position of the saw blade.

Fences and Adjustments

Rip Fence

How to use and adjust the rip fence for parallel cuts.

Mitre Fence

How to fit and use the mitre fence for angled cuts.

Assembly and Connection

Installation of Legs

Step-by-step guide for attaching the machine's legs.

Connect to Dust Collector

Instructions for connecting a dust extraction system to the machine.

Dust Collection and Mitre Fence Assembly

Dust Collection from Chip Casing

How to attach the dust port to the chip casing.

Dust Collection from Blade Guard

How to connect the dust spout from the blade guard.

Mitre Fence Assembly

Detailed steps for assembling the mitre fence components.

Mains Connection

Electrical Hazard

Warnings regarding electrical safety during operation.

Change of Direction of Rotation

How to check and correct the motor's rotation direction.

Operation

Pre-operation Checks

Essential checks before starting the machine.

Personal Protective Equipment

Recommended gear for user safety during operation.

Work Position

Correct posture and positioning for safe sawing.

Kickback Danger

Risks associated with kickback and how to prevent it.

Dress Code

Safety precautions regarding clothing and hair during operation.

Rip Cuts with Rip Fence

Reposition Auxiliary Fence Extrusion

Adjusting the auxiliary fence for different stock thicknesses.

Set Depth of Cut

How to set the correct blade depth relative to the workpiece.

Care and Maintenance

Servicing Precautions

Safety measures to take before performing any maintenance.

Replacement Parts

Guidance on using genuine and approved replacement parts.

Saw Blade Change

Removing Table Sections

How to remove parts of the table to access the blade.

Taking Blade Guard Off

Procedure for removing the blade guard for blade access.

Cleaning Clamping Surfaces

Importance of clean surfaces for secure blade mounting.

Mounting a Fresh Saw Blade

Correct procedure for installing a new saw blade.

Saw Blade Arbor Nut

How to tighten the arbor nut and safety warnings.

Use of Cleaning Agents

Warnings about using incorrect cleaning agents on saw components.

Saw Blade Restrictions

Types of saw blades that should not be used.

Saw Blade Adjustment

Parallelism Adjustment

Setting the blade parallel to the table edge within 3 mm.

Turning Saw Over

Step for inverting the saw to access adjustment nuts.

Tightening Nuts

Securing the saw blade adjustment.

Swivel Segments Setting

Adjusting swivel segments and avoiding tightening during operation.

Drive Belt Tensioning

Checking Belt Tension

Methods to determine if the drive belt needs tensioning.

Adjusting Motor Housing

How to adjust belt tension by moving the motor.

Riving Knife Setting

Distance to Saw Blade

Setting the correct gap between the saw blade and the riving knife.

Lateral Offset

Aligning the riving knife with the saw blade for trial cuts.

Blade Tilt Stop Setting

Adjusting Backstop Setting Screws

Fine-tuning the stops for accurate angle settings.

Scale Setting

Rip Fence Scale Calibration

Aligning the scale's "0" mark with the rip fence.

Universal Fence Adjustments

Fence Squareness Check

Ensuring the fence is perpendicular to the saw blade.

Mitre Scale Adjustment

Adjusting the mitre scale for precise angle cuts.

Cleaning the Saw

Machine Transportation

Machine Storage

Troubleshooting

Motor Does Not Run

Diagnosing and resolving issues when the motor fails to start.

Reverse Rotation of Saw Blade

Correcting the saw blade's rotation direction for three-phase motors.

Loss of Cutting Performance

Addressing issues like dull blades causing poor cuts.

Technical Specifications

Electrical Specifications

Voltage, current, fuse protection, and protection class details.

Motor and Blade Specifications

Motor capacity, speed, and saw blade dimensions.

Noise Emission Values

Sound pressure and power levels during operation.

Available Saw Blades

Information on recommended saw blades for different applications.

Circuit Diagrams

Single-phase Motor Circuit

Wiring diagram for the single-phase motor setup.

Three-phase Motor Circuit

Wiring diagram for the three-phase motor setup.

EC Declaration of Conformity

Machine Directive Compliance

Confirmation of compliance with the EC Machine Directive.

Electromagnetic Compatibility

Confirmation of compliance with EMC directives.

Low Voltage Directive Compliance

Confirmation of compliance with the EC Low Voltage Directive.

Harmonized Standards

List of applied harmonized and national standards.

Type Test Certificate

Details of the type test carried out by a notified body.

Company Contact Information