Elektra Beckum BAS 315/4 GDN 55 User Manual

ELEKTRA BECKUM [1
®
M
m
m
# ■
;I!i
Betriebsanleitung Band sage
Operating Instructions Band Saw
Instruction de service Scie a ruban
Istruzioni di servizio Sega a nastro
Gebruiksaanwijzing Bandzaag
Driftsvejledning Bandsav
Bruksanvisning Bandsag
Handbok Bandsag
Kayttoohje Vannesaha
BAS 315/4 GWN 55
BAS 315/4 GDN 55
^ Achtung! Bitte lesen Sie diese Betriebsanleitung vor der Installation und Inbetriebnahme der Bandsage aufmerksam durch.
Note Read these instructions carefully before commissioning and operating this band saw.
Attention! Priere de lire attentivement cette instruction de service avant installation et mise en service de la scie a ruban.
Attenzione! Si prega de leggere con attenzione e completamente le istruzioni di servicio prima dell’installazione e della messa in
esercizio della sega a nastro.
Let op! Lees deze gebruiksaanwijzing a.u.b. zorgvuldig door voor de installatie en het gebruik nemen van de bandzaag.
Vigtigt! De bedes lasse driftsvejledningen opmaerksomt i gennem inden installationen og idrifttagningen af bandsaven.
OBS! Vser vennlig a lese noye gjennom denne bruksanvisningen for du installerer og tar i bruk bandsagen.
Observera! Innan bandsagen installeras och tas i drift skall instruktionerna i handboken lasas noggrant.
Huomio! Lue kayttoohje huoleliisesti lapi ennen vannesahan asennusta ja kayttoonottoa.
Atehcion! Por favor, lea cuidadosamente las instrucciones de servicio antes de la instalacion y puesta
^ en marcha de la sierra de cinta._
Technische Anderungen vorbehalten! / Eiektra Beckum reserves the right to change specifications and design without prior notice and without incurring
obligation of any kind. Equipment referred to as available or optional may be at extra cost. I Sous reserve de modifications techniques! / Con riserva di
modifiche tecniche / Technische wijzigingen voorbehouden! / Ret til tekniske send ringer forbeholdes! / Med forbehold om tekniske endringer! / Forbehall
for tekniska andringar! I Oikeus teknisiin muutoksiin pidataan. I Moditicaciones t’ecnocas reservadas.
0598 - D/GB/F/l/NLVDK/N/S/SF/E
Art.-IMr. 115 161 0915

Elektra Beckum BAS 315/4 GDN 55 Specifications

General

Saw type	Band saw
Voltage	230 V
Cutting height max.	170 mm
Cutting width max.	305 mm
Saw band length	2240 mm
Saw band width	6-12 mm
Table tilt	0-45°
Cutting speed	800 m/min
Blade diameter	Not applicable
Max cutting depth at 90°	Not applicable

Summary

General

Specifications

Technical details and dimensions of the band saw models.

User Responsibility and Warranty

Defines user obligations, maintenance, and warranty terms.

Final Assembly and Installation

Step-by-step guide for unpacking and assembling the band saw.

Settings

Selecting the Correct Blade Speed

Guidance on choosing the appropriate blade speed for different materials.

Changing and Setting the Saw Blade

Instructions for replacing and correctly tensioning the saw blade.

Blade Guiding

Procedure for setting up the blade guides for precise cutting.

Setting the Cutting Height

How to adjust the upper blade guide to the desired cutting height.

Saw Table Tilt

Instructions for tilting the saw table for bevel cuts.

Safety Information

Comprehensive safety guidelines, hazards, and precautions for operating the band saw.

Other Information

Details on optional accessories and intended use of the machine.

Electrical Installation

Requirements for connecting the band saw to the power supply safely.

Accessories

Mitre Fence

Details on the mitre fence accessory for angled cuts.

Workstand

Information on the optional workstand for stable setup.

Bandsaw Blades

Wiring Diagrams

Spare Parts List