3 Safety
3.1 General safety instructions
These operation and installation instructions include all
safety instructions for prevention and avoiding of dangers
during handling of the product over its entire life cycles.
Compliance with all specifi ed safety instructions ensures
safe operation of the product.
3.2 Layout of safety instructions
The safety instructions in this document are marked by dan-
ger signs and safety symbols and are designed according
to the SAFE principle. They include information on type and
source of the danger as well as on possible consequences
and on prevention of the danger.
The following table defi nes the design and description of the
levels of danger with potential physical injuries as they are
used in these operating instructions.
Symbol Signal
word
Description
DANGER Warns of a potential ac-
cident with if instructions
are not complied with
leading to life-threatening,
irreversible injuries or
death.
WARNING Warns of a potential ac-
cident with if instructions
are not complied with lea-
ding to severe, potentially
life-threatening, irreversib-
le injuries or death.
CAUTION Warns of a potential ac-
cident with if instructions
are not complied with
leading to light, reversible
injuries.
Fig. 1 Notation of personal injury
The following table describes symbols used in these ope-
rating instructions for illustration of dangerous situations
in connection with the respective symbol for the level of
danger.
Symbol Description
Danger due to voltage, electrical shock:
This symbol indicates dangers due to
electricity.
Fig. 2 Notation of a specifi c danger
The following table defi nes the illustration and description
of situations in these operating instructions that may lead
to damage to the product or indicates facts, conditions, tips
and information.
2 | US+CA © elero GmbH
Intended use | Safety
ved at all times. Apart from the safety instructions in these
operating instructions, applicable local regulations on pre-
vention of accidents, environmental protection and occupa-
tional safety must be observed. Regulations and standards
for safety assessment can be found in the EC Declaration
of Conformity.
2.2 Intended use
This product is intended for use in facade construction for
driving electrical sun protection devices.
Decisive for the determination of the drive system is the
elero drive computation program (http://elero.com/
en;service;drive-computation-program.htm).
Other applications must be approved in advance by the ma-
nufacturer elero GmbH Antriebstechnik (refer to „Address“).
The operator alone is liable for all damage due to improper
use of the product. The manufacturer does not assume any
liability for personal injuries and property damage due to
misuse or procedural violations by improper use or commis-
sioning.
The product may only be operated by trained and autho-
rized personnel under observation of all safety instructions.
Safe and correct operation and operational safety of the
product is subject to operation according to its intended use
according to the provisions of these operating and installati-
on instructions.
The intended use includes observance and compliance of
all safety instructions included in these operating instruc-
tions and all applicable regulations by the trade association
and applicable laws for environmental protection. The inten-
ded use also includes compliance of all company regulati-
ons included in these operating and installation instructions.
2.3 Foreseeable misuse
Foreseeable misuse includes operating the product not in
accordance with the intended use approved by the manu-
facturer elero GmbH Antriebstechnik (refer to „Address“).
2.4 Warranty and liability
Generally, the general terms and conditions of sale and
delivery of the manufacturer elero GmbH Antriebstechnik
(refer to „Address“) apply. The terms and conditions of sale
and delivery are part of the sales documentation and are
handed over to the operator on delivery. Liability claims for
personal and property damage are excluded if such dama-
ge is due to one or several of the following causes:
• Opening the product by the customer
• Improper use of the product
• Incorrect installation, commissioning or operation of the
product
• Structural changes to the product without the written
approval of the manufacturer
• Operating the product with incorrectly installed connec-
tions, defective safety equipment or with not properly
installed safety and protective equipment
• Failure to observe the safety regulations and instructions
included in these operating instructions
• Non-compliance with the specifi ed technical data
2.5 Customer service of the manufacturer
In case of a defect, the product may only be repaired by
the manufacturer. Please refer to section „Address“ for the
return address of the customer service.
If you did not acquire the product directly from elero, please
contact your supplier.
To Next Page
Loading...
