How to fix no display message on ELGA PURELAB Option-R15?
If there is no display message on your ELGA Water Dispenser, verify the mains supply and lead are properly connected. Ensure the mains power is switched on. Also, inspect the fuse in the power inlet module and replace it if it's blown.
What to do if ELGA PURELAB Option-R15 output flow is outside specification?
If the output flow of your ELGA Water Dispenser is outside the specified range, start by checking the supply pressure. Then, compare the RO flow-rate of your unit against the graphs detailed in Section 3.3 of the manual, paying attention to treated water output in relation to temperature and feedwater pressure. Ensure the inlet strainer and receiver strainer are clean. If necessary, consider contacting a service technician to install or replace an optional booster pump.
What to do if the reservoir low level audible alarm sounds on my ELGA PURELAB Option-R15?
If the reservoir low level audible alarm sounds on your ELGA Water Dispenser, you can press the crossed bell button to mute the alarm. The reservoir should then automatically refill. Check that the process mimic shows the reservoir filling. Also, verify the feedwater supply and the connections to the reservoir.
How to fix no flow from dispense tap on ELGA Water Dispenser?
If there is no flow from the dispense tap of your ELGA Water Dispenser, push the PROCESS button. Also, ensure that the reservoir level is above 40%.
What to do if UV lamp failure audible alarm sounds on ELGA PURELAB Option-R15?
If the UV lamp failure audible alarm sounds on your ELGA Water Dispenser, you can press the crossed bell button to mute the alarm. Check that all electrical connections are secure. When applicable, follow the UV lamp replacement procedure. You can also temporarily continue operation without the UV lamp if necessary.
How to stop ion-exchange cartridge replacement alarm on ELGA PURELAB Option-R15 Water Dispenser?
If the ion-exchange cartridge replacement alarm is active on your ELGA Water Dispenser, replace the ion-exchange cartridge pack.
What to do if pre-treatment cartridge replacement alarm sounds on ELGA Water Dispenser?
If the pre-treatment cartridge replacement alarm is active on your ELGA Water Dispenser, replace the pre-treatment cartridge.
Lists the different PURELAB Option-R models available.
Provides guidance on how to use the operator manual effectively.
Details how to obtain service support and consumable items.
Highlights critical safety information regarding electricity, pressure, UV light, and chemicals.
Describes the PURELAB Option-R unit and its purpose.
Explains the water purification stages and technologies used by the unit.
Details electrical requirements, dimensions, connections, and performance data.
Explains the function of the control panel, buttons, and display icons.
Covers the initial steps of unpacking the unit.
Provides guidance on selecting a suitable location and environment for the unit.
Provides instructions for connecting water tubes, electrical supply, and reservoir level control.
Guides through setting up system preferences like auto-restart, alarms, and water purity units.
Details the procedure for the first-time start-up, including system rinsing.
Explains how to dispense water and the automatic intermittent mode for maintaining purity.
Describes various alarms, their causes, and how to acknowledge them.
Identifies the unique replacement consumables designed for the unit.
Recommends the service life for consumables based on typical usage.
Step-by-step guide for replacing the LC140 pre-treatment cartridge.
Instructions for removing and replacing the LC141 ion-exchange cartridge pack.
Procedure for changing the LC105 ultraviolet lamp.
Details on how to check and clean the inlet strainer.
Details on how to check and clean the re-circulation strainer.
Information on when to replace the LC143 reverse osmosis cartridge.
Outlines the complete procedure for sanitizing the unit and reservoir.
Specific steps for sanitizing both the unit and the reservoir.
Provides safety information and handling precautions for the CT1 sanitization tablet.
Lists common issues, their causes, and recommended actions for resolution.
Catalogues of available consumables, their service life, and accessories with part numbers.
Defines the various icons used on the control panel.
Details the icons and conditions that signify specific alarms.
Explains the icons and presets related to cartridge replacement timers.
Shows screen examples for low level, quality, and standby alarms.
Outlines the warranty terms for manufactured products.
Specifies the warranty terms for water systems, excluding membranes and cartridges.
Provides contact details for ELGA LabWater and additional resources.
General| Brand | ELGA |
|---|---|
| Model | PURELAB Option-R15 |
| Category | Water Dispenser |
| Language | English |
To Next Page
