Eliwell EM300 - Parameter Table (V;I & Pt100-TC); Alarm Parameters (V;I & Pt100-TC); Communication Parameters (V;I & Pt100-TC); Configuration Parameters (V;I & Pt100-TC)

EM300(LX) 5/6
PARAMETER
HA1 (!)
LA1 (!)
AFd
PAO (!)
tAO
tP
H00 (!)
H03
H04
rEL
tAb
* DEFAULT column: for these parameters the default depends
on the model.
(!) CAUTION!
• If one or more parameters marked with (!) are modified, the device must be switched off after the modification and then switched back on
•PLEASE NOTE: We strongly recommend that you switch the instrument off and on again each time parameter configuration is changed in order to prevent malfunction-
ing of the configuration and/or ongoing timings.
DESCRIPTION
ALARMS (folder with “rE1” label)
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
Higher ALarm. Maximum temperature alarm. Temperature value
(considered as absolute value) which if gone above triggers the alarm
signal.
Lower ALarm. Minimum temperature alarm. Temperature value
(considered as absolute value) which if gone below triggers the alarm
signal.
ALARMS (folder with “AL” label)
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
Alarm Fan differential. Alarm differential.
Power-on Alarm Override. Alarm exclusion time after instrument
start-up, after a power failure.
Temperature Alarm Override. Temperature alarm signal delay
time.
silences alarm using button
COMMUNICATION (folder with “Add” label) LX MODELS ONLY
SEE
SEE
EM300
EM300
T
T
ABLE above DISPLA
ABLE above DISPLA
Y (folder with “
Y (folder with “
diS” label)
diS” label)
SEE
SEE
EM300
EM300
T
T
ABLE above
ABLE above
V/I
V/I
MODELS
MODELS
ONL
ONL
Y:
Y:
NOTE 1: ndt parameter has range n/y/int int=whole numbers.
NOTE 2: LdL has range -99...HdL or -99.9...HdL or -999...HdL
according to ndt parameter setting HdL has range -LdL...100 or
-LdL...100.0 or -LdL...1000 according to ndt parameter setting
CONFIGURA
CONFIGURA
TION (folder with “CnF” label)
TION (folder with “CnF” label)
Selection of probe type
Minimum value of voltage / current input
Maximum value of voltage / current input
Device version. Read only parameter.
Reserved. Read only parameter.
COPY CARD (folder with “Fpr” label)
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
SEE EM300 TABLE above
DEFAULT*
*
(§) 1200
*
(§) -200
2.0
0
0
y
(§) 2
*
*
/
/
RRAANNGGEE ((VV//II))
LA1...150.0
-50.0...HA1
1.0...50.0
0...10
0...250
n/y
NOTE 3:
NOTE 3:
the dro parameter is
the dro parameter is
not present
not present
§§§
-99.0…100.0
(ndt= y)
-999…1000
(ndt= int)
as above
/
/
VALUE**
U.M.
°C/°F
°C/°F
°C/°F
hours
min
flag
num
C/°F
C/°F
/
/
PARAMETER TABLE FOR EM300(LX) with V/I & Pt100-TC input
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
LX
LX
MODELS
MODELS
ONL
ONL
Y
Y
§§§
010/05/01 for VOLTAGE INPUT
420/020 for CURRENT INPUT
(§) Pt100/TC model
RRAANNGGEE ((PPtt110000))
LA1...1999
-328...HA1
1.0...50.0
0...10
0...250
n/y
NOTE 3:
NOTE 3:
the dro
the dro
parameter is
parameter is
present
present
(§) Jtc/HtC/Pt1
not present
not present
/
/