Prog
OK
OK
PRG
+
Auto
ESC
OK
OK
OK
OK
OK
OK OKOK OK OK OK
OK
Prog
+
_
+
_
+
_
+
_
+
_
+
_
OK
OK
OK
OK
Prog
+
_
+
_
+
_
+
_
+
_
+
_
ProgProg
°C
Prog
°C
Prog
ESC
OK
OK OK OK
Prog
Prog Prog
Prog
ProgProg Prog
OKOK
+
_
+
_
+
_
OK
Prog
+
_
Prog Prog
OK
+
_
OK
ProgProg
+
_
Prog
on
Prog
°C
CR2032
+
PRG
Auto
Prog
ter
Performed by shortly pressing the hidden RESET button with a blunt-pointed object (e.g. a pencil
or screw-driver with a diameter of at most 2 mm).
The type of device and software version will be displayed for 1 second, then the device will enter
default mode. This means that the language is set to EN, all data is zeroed (thermostat function,
time/date, user programs, device options function).
Reset
press button
OK
to complete
the deleting of all set programs
in starting menu (time is shown
on display) - press simultaneously
button
PRG
and
OK
and display
announces a notice all
Deleting of all programs
all
16--sep-- 10
An example of TER-9 programming
Battery replacement
You can change the battery without disassembling the device.
CAUTION
- only change the battery when the device is disconnected from power supply !!!
- the date and time must be reset after changing the battery !!!
- remove the plug-in module with the battery
- replace the original battery
- enter a new battery so that its upper edge (+) lines up with the plug-in module
- slide the plug-in module in the device and pay attention to polarity (+ up) – for roughly 1 s,
the display will show the name and the software version
- you can connect the device to power supply
Setting the TER-9 in the function: two dependent thermostats with temperature setting T1 = 10°C a T2 20 °C with hysteresis setting T1 = 2 °C a T2 = 1°C.
With automatic controlled temperature change on 18.11.2010 at 6:52 p.m. to the temperature T1= 15 °C.
function function temperatur temperatur
temperatur hysteresi
hysteresi hysteresi
set
channel channelchannel
channel channel
time prog add
add
prog year prog
year month day hour minute
day prog
- long press (>1s)
- short press (<1s)
16--sep-- 10
16--sep-- 10
Warning
Device is constructed for connection in 1-phase main alternating current voltage AC 230 V or
24 V AC/DC (based on type of device) and must be installed according to norms valid in the
state of application. Connection according to the details in this direction. Installation, con-
nection, setting and servicing should be installed by quali ed electrician sta only, who has
learnt these instruction and functions of the device. This device contains protection against
overvoltage peaks and disturbancies in supply. For correct function of the protection of this
device there must be suitable protections of higher degree (A, B, C) installed in front of them.
According to standards elimination of disturbancies must be ensured. Before installation the
main switch must be in position “OFF” and the device should be de-energized. Don´t install
the device to sources of excessive electro-magnetic interference. By correct installation en-
sure ideal air circulation so in case of permanent operation and higher ambient temperature
the maximal operating temperature of the device is not exceeded. For installation and setting
use screw-driver cca 2 mm. The device is fully-electronic - installation should be carried out
according to this fact. Non-problematic function depends also on the way of transportation,
storing and handling. In case of any signs of destruction, deformation, non-function or missing
part, don´t install and claim at your seller it is possible to dismount the device after its lifetime,
recycle, or store in protective dump.
To Previous Page
Loading...
