What should I do if the casing of my Elma Dental equipment is damaged?
If the casing of your Elma Dental equipment is damaged, it's likely due to an external cause, such as transport damage. In this case, return the unit to the supplier or manufacturer.
What to do if my Elma Ultrasonic Jewelry Cleaner has an insufficient cleaning result?
If you're experiencing insufficient cleaning results with your Elma Ultrasonic Jewelry Cleaner, consider the following: * You might be using no cleaning chemical or an unsuitable one. Use a suitable cleaning chemical. * The cleaning temperature might be unfavorable. Heat up the cleaning liquid. * The cleaning time might be too short. Repeat the cleaning cycle.
Why is the heating time unsatisfactory in my Elma Ultrasonic Jewelry Cleaner?
An unsatisfactory heating time in your Elma Ultrasonic Jewelry Cleaner could be due to: * Heating energy loss. Use a cover (optional accessory equipment). * The cleaning liquid not being stirred. Switch on ultrasound.
What to do if my Elma Ultrasonic Jewelry Cleaner unit is out of service and the LED display is dark?
If your Elma Ultrasonic Jewelry Cleaner's LED display is dark and the unit is out of service, there could be several reasons: * The mains cable might not be connected. Ensure it is properly plugged in. * The mains socket might be dead. Check the socket and fuse. * The mains cable could be damaged. Replace it if necessary. * There may be an electronic error. In this case, return the unit to the supplier or manufacturer.
Why is my Elma Ultrasonic Jewelry Cleaner not operating ultrasound and the LED display is dark?
If the ultrasound on your Elma Ultrasonic Jewelry Cleaner isn't working and the LED display is dark, consider these possibilities: * The unit might be switched off. Turn it on using the on/off key. * The ultrasound key might not have been pressed. Press the ultrasound key to activate it.
Why does my Elma Dental equipment make boiling noises during heating?
If your Elma Dental equipment makes boiling noises during heating, it is likely due to no stirring of cleaning liquid. To resolve this, switch on ultrasound.
Why is the set temperature exceeded on my Elma Dental equipment?
If the set temperature is exceeded on your Elma Dental equipment, it could be due to several reasons: * The temperature sensor might not be measuring the average temperature because the liquid is not being stirred. To resolve this, stir the liquid by hand or by ultrasound. * The set temperature might be too low. For low set temperatures, do not switch on heating. * Ultrasonic energy may be heating up the cleaning liquid. Switch on ultrasound for a short period.
What does it mean if heating is not operating and Error: 2 is displayed on my Elma Dental equipment?
If the heating is not operating and Error: 2 is displayed on your Elma Dental equipment, it is likely due to an electronic error. To attempt to resolve this, switch the unit off and on again. If the error persists, return the unit to the supplier or manufacturer.
What to do if the casing of my Elma Ultrasonic Jewelry Cleaner is damaged?
If the casing of your Elma Ultrasonic Jewelry Cleaner is damaged due to an external cause like transport damage, return the unit to the supplier or manufacturer.
What to do if my Elma Ultrasonic Jewelry Cleaner gives an Error: 2 when heating is not operating?
If your Elma Ultrasonic Jewelry Cleaner displays 'Error: 2' and the heating is not operating, it could be due to an electronic error. Switch the unit off and on again; if the error occurs again, return the unit to the supplier or manufacturer.
Key safety guidelines and warnings for operating the ultrasonic cleaning unit.
Guidance on how to read and understand the operating instructions and safety symbols.
Explains the four key factors influencing ultrasonic cleaning results: energy, media, temperature, and time.
Step-by-step guide on how to perform the ultrasonic cleaning procedure.
Details the key features and specifications of the ultrasonic cleaning unit.
Unit compliance with CE marking and list of items included in the package.
Identifies and describes the main controls and indicators on the front of the unit.
Identifies the ports and connections located on the rear of the unit.
Explains the function and operation of the drain knob for emptying the tank.
Details each button, knob, and LED on the unit's control panel and their functions.
Explains the meaning of the different indicators and values shown on the unit's display.
Summarizes common intended actions, what to do, and the resulting display.
Instructions for unit placement, ambient conditions, and drain duct preparation.
Steps for safely connecting the ultrasonic cleaning unit to the electrical power supply.
Instructions for correctly shutting the drain duct and filling the tank with cleaning liquid.
Details on how to heat the cleaning liquid and important safety notes regarding temperature.
Explains the stirring mode that mixes the liquid during the heating-up process.
Describes how to remove air bubbles from cleaning liquids for improved ultrasonic effect.
Important warnings about hot surfaces, liquids, and noise emission during ultrasonic cleaning.
Step-by-step guide to initiate an ultrasonic cleaning cycle using manual controls.
Procedure for starting cleaning automatically once the set temperature is reached.
Details on activating and using the Degas mode for efficient degassing of liquids.
Explanation of the Sweep mode for achieving a more homogeneous sound field distribution.
How to activate the Pulse mode to intensify ultrasonic cleaning effect.
Instructions on selecting frequency, power, and time for optimal cleaning results.
Guidelines for placing items, rinsing, and draining the unit after cleaning.
Critical warnings and restrictions for using solvents and aqueous cleaners in the ultrasonic bath.
Lists Elma cleaning concentrates for dental applications.
Lists Elma cleaning concentrates for medical applications.
Lists Elma cleaning concentrates for optical lenses and components.
Lists Elma cleaning concentrates for laboratory use and sensitive materials.
Instructions for safe maintenance, electrical checks, and cleaning of unit components.
Tips and recommendations to prolong the service life of the transducer tank.
Information on authorized personnel for repair and maintenance, and liability.
Table detailing tank capacity, dimensions, weight, voltage, frequency, and power for various models.
Lists common issues like unit errors, heating problems, and insufficient cleaning with causes and solutions.
Provides contact details for the manufacturer and suppliers for further assistance.
General| Brand | Elma |
|---|---|
| Model | Elmasonic P |
| Category | Dental equipment |
| Language | English |
To Next Page
