To Next PageTo Next PageWhy does the Elma Elmasteam 8 Steam Cleaner show a warning and not allow steam operation?
The Elma Steam Cleaner might show a warning and prevent steam operation in soft or strong mode because the foot switch isn't properly connected. Check the foot switch plug to ensure it's fully screwed in. If it isn't, plug it in correctly.
What to do if the Elma Steam Cleaner pump operation does not switch off?
If the pump operation on your Elma Steam Cleaner doesn't switch off, there are several potential causes: * The white hose in the canister may have slipped upwards. To fix this, unscrew the canister lid and adjust the white-water hose and filling level cable with float switch to the same level, then repeat the commissioning process for the pump. * The sieve in the water connection could be clogged. Remove the sieve and clean it. * Seals in the fixed-water supply or the water connection to the canister might be missing. Insert a seal in the fixed-water connection and/or in the water connection to the canister. Check if the seal remained displaced on the device, on the connection to the device when unscrewing the water connection. * There may be air in the water supply.
Why is steam suddenly exiting on the housing of my Elma Elmasteam 8 Steam Cleaner?
If steam suddenly exits on the housing (rear side of the device) of your Elma Steam Cleaner, accompanied by a possible one-off creaking sound and a flashing gauge, it indicates that the safety valve has triggered. In this case, disconnect the mains plug or switch off the device at the mains switch. For devices with compressed air: inspect whether the maximum permissible connection supply pressure was observed.
How to fix Elma Elmasteam 8 when service flashes and no steam operation is possible?
If the service indicator flashes, a signal tone sounds, and no steam operation is possible in soft or strong mode on your Elma Steam Cleaner, it means that descaling was not carried out, triggering a safety shut-down. To resolve this, descale the device.
Why Elma Elmasteam 8 is not working and warning flashes?
If the warning light flashes and no steam operation is possible in soft or strong mode on your Elma Steam Cleaner, it could be due to the foot switch not being properly connected when using the steam operation via fixed nozzle. Inspect the plug for the foot switch to ensure it is screwed in up to the stop, or simply plug in the foot switch plug.
What to do if Elma Elmasteam 8 pump is not pumping?
If the pump is not pumping, the filling level flashes, and the warning light flashes on your Elma Steam Cleaner, it could be due to a couple of reasons. First, the 30 seconds waiting time may not have been observed; pumping operation starts initially 30 seconds after switching on. Alternatively, the filling level might be too low; fill the device manually with at least 2 liters of water.
What to do if Elma Elmasteam 8 has steam exiting on housing?
If steam suddenly exits on the housing (rear side of the device) of your Elma Steam Cleaner, and you hear a creaking sound with gauge flashes, the safety valve has triggered. Disconnect the mains plug or switch off the device at the mains switch. For devices with compressed air: inspect whether the maximum permissible connection supply pressure was observed.
What to do if the Elma Elmasteam 8 pump doesn't switch off?
If the pump operation on your Elma Steam Cleaner doesn't switch off, it could be because the white hose in the canister has slipped upwards. To fix this, unscrew the canister lid and adjust the white water hose and filling level cable with float switch to the same level. Then, repeat the commissioning process for the pump. Alternatively, the sieve in the water connection could be clogged. Remove the sieve and clean it.
Why does the operating display on my Elma Steam Cleaner not illuminate?
If the operating display on your Elma Steam Cleaner does not illuminate, it indicates a malfunction. In this case, send the device to the service center.
What to do if the pressure value achieved is not displayed in ascending order on the scale of values of Elma Elmasteam 8?
If the pressure value achieved is not displayed in ascending order on the scale of values on your Elma Steam Cleaner, it indicates a heating malfunction. In this case, send the device to the service center.
General| Brand | Elma |
|---|---|
| Model | Elmasteam 8 |
| Category | Steam Cleaner |
| Language | English |
Instructions on using the manual, symbols, and signal words for safe operation.
Explanation of warning symbols and text displayed on the device for safety.
Covers intended use, warranty, personnel, installation, and electrical safety.
Specific instructions for using the device with medical instruments and safety.
Covers packaging, environment, and electrical connection requirements for setup.
Instructions for connecting the fixed water supply hose.
Guide for connecting the water supply from an external canister.
Specifies water type, conductivity, and salt usage for optimal device performance.
Describes automatic filling from a fixed water supply with safety precautions.
Detailed guide on using the handpiece for steam and compressed air functions.
Instructions for operating the device using the fixed nozzle and foot switch.
Step-by-step instructions for descaling the device, including water and duration.
Instructions for flushing the pressure vessel, often linked to descaling.
Warnings and procedures for device repairs, emphasizing qualified personnel.
Guide to diagnose and resolve device errors, leaks, and operational issues.
