Emerson Dixell iProChill IPC115D - Configure Analogue and Digital Inputs;Outputs; Digital Inputs Configuration; Analogue Inputs Configuration

1592025050 iProChill v2.5 10D00 AG v1.3 GB 18.02.2016.docx iProCHILL 157/205
9. ANALOGUE - DIGITAL INPUTS/OUTPUTS CONFIGURATIONS
On board of the controller, it allows to configure 20 DI, 15 DO, 10 AI and 6 AO in maximum. If more I/O
needed, please use expansion module IPROEX60D. For one IPROEX60D, it can connect with 3 DI, 6 DO, 7
AI and 3 AO. It can has 4 IPROEX60D at most. In addition, 4 electronic thermostatic drivers XEV20D can
provide 16 more AI (4 for each).
Use parameters in group IO to configure analogue-digital inputs/outputs.
DIGITAL INPUTS CONFIGURATION
 IO11 – IO30: On board DI (1 - 20)
 IO75 – IO77: 1
st
expansion DI (1 - 3)
 IO94 – IO96: 2
nd
expansion DI (1 - 3)
 IO113 – IO115: 3
rd
expansion DI (1 - 3)
 IO132 – IO134: 4
th
expansion DI (1 - 3)
DIGITAL OUTPUTS CONFIGURATION
 IO31 – IO45: On board relays (1 - 15)
 IO78 – IO83: 1
st
expansion relays (1 - 6)
 IO97 – IO102: 2
nd
expansion relays (1 - 6)
 IO116 – IO121: 3
rd
expansion relays (1 - 6)
 IO135 – IO140: 4
th
expansion relays (1 - 6)
ANALOGUE INPUTS CONFIGURATION
 IO01 – IO10: On board probes (1 - 10)
 IO52 – IO55: 1
st
XEV20D probes (1 - 4)
 IO56 – IO59: 2
nd
XEV20D probes (1 - 4)
 IO60 – IO63: 3
rd
XEV20D probes (1 - 4)
 IO64 – IO67: 4
th
XEV20D probes (1 - 4)
 IO68 – IO74: 1
st
expansion probes (1 - 7)
 IO87 – IO93: 2
nd
expansion probes (1 - 7)
 IO106 – IO112: 3
rd
expansion probes (1 - 7)
 IO125 – IO131: 4
th
expansion probes (1 - 7)
ANALOGUE OUTPUTS CONFIGURATION
 IO46 – IO51: On board AO (1 - 6)
 IO84 – IO86: 1
st
expansion AO (1 - 3)
 IO103 – IO105: 2
nd
expansion AO (1 - 3)
 IO122 – IO124: 3
rd
expansion AO (1 - 3)
 IO141 – IO143: 4
th
expansion AO (1 - 3)
Note:
For digital inputs/outputs, it is possible to select polarity. In I/O configuration, use prefix “o” to indicate “open”
polarity which means the DI/DO is activated when contact is open; use prefix “c” to indicate “close” polarity
which means the DI/DO is activated when contact is closed.
For example:
IO11 = o1 - Remote ON/OFF
IO11 = c1 - Remote ON/OFF
They all mean DI01 is configured as “Remote ON/OFF” but with different polarity. And the DI type is 1.
In the paragraphs below, we will use “DI type”, “DO type”, “AI type” and “AO type” to indicated function
index of all the I/O.
For analogue inputs/outputs, it is also possible to configured as digital inputs/outputs. For example an AI can
assume values from 0 to 66 (if configured as analog) and from 67 (that correspond to o1) to 296 (that
correspond to c115).
Remember that:
 AO1, AO2, AO3 and AO4 can be configured only as 0-10V;
 AO5 and AO6 can be configured as 0-10V, PWM and 4-20mA;
 in the expansions modules, the AO can be configured only as 0-10V.