Emerson FB2200 - Page 121

Emerson FB2200 Flow Computer Instruction Manual
D301784X012
March 2019
Index 117
4-2. Infrared (IR) Button Location ......................... 85
5-1. FB2100 Flow Computer Components ............ 88
5-2. LED Locations ................................................ 89
5-3. Switch and Buttons ....................................... 91
5-4. Captive Fastening Screws .............................. 92
5-5. Main Battery Pack .......................................... 93
5-6. Remove Plastic Tabs from New Battery
Pack ................................................................. 94
5-7. Loosen Captive Fastening Screws and Rotate
Assembly Forward ............................................ 95
5-8. Pry out the old battery pack – leave
connected to cable ........................................... 96
5-9. Remove the Termination Cover (if present) ... 97
5-10. Unstrap the Old Battery Pack – Leave
Connected to Cable .......................................... 97
5-11. Old Battery (left) and New Battery (right)
Sit on Enclosure ................................................ 98
5-12. Connect New Battery – Both Now
Connected ........................................................ 98
5-13. Old battery disconnected, new battery
connected ........................................................ 99
5-14. Thread the Battery Strap ........................... 100
5-15. Ease the Battery into the Battery
Compartment ................................................ 100
5-16. Tighten the Battery Strap .......................... 101
5-17. Opening in the Battery Strap ..................... 101
5-18. Loosen the captive fastening screws .......... 103
5-19. Removing the CPU Enclosure Cover ........... 103
5-20. Coin Cell Battery Removal/Replacement.... 104
5-21. Firmware Update Dialog Box ..................... 105
A-1. Data Plate (Fiberglass w/no battery)-Class I
Div 2 Non-incendive (UL) ................................ 108
A-2. Data Plate (Fiberglass w/Lead acid battery) -
Class I Div 2 Non-incendive (UL) ...................... 108
A-3. Data Plate (Fiberglass w/no battery, relay) -
Class I Div 2 Non-incendive (UL) ...................... 109
A-4. Data Plate (Aluminium w/no battery) - Class I
Div 2 Non-incendive (UL) ................................ 109
A-5. Data Plate (Aluminum w/Lead acid battery)
Class I Div 2 Non-incendive (UL) ...................... 110
A-6. Data Plate (Aluminum w/no battery, relay)
Class I Div 2 Non-incendive (UL) ...................... 110
B-1. Data Plate (Fiberglass w/no battery) – ATEX
nA Non-Sparking ............................................ 112
Firmware
upgrading the .................................................... 104
H
Hazardous locations
ATEX Zone 2 ...................................................... 111
Class I Division 2 ................................................ 107
Hazardous Locations ............................................... 11
HMI module
replacing ............................................................. 92
HMI Module
buttons ............................................................... 84
HMI Screen saver mode
on HMI display ..................................................... 84
Human-Machine Interface (HMI) Module .................. 8
I
I/O
configuration and wiring ..................................... 61
options .................................................................. 5
Installation .............................................................. 11
L
LCD
replacing ............................................................. 92
LEDs
meaning of .......................................................... 89
Low power mode .................................................... 30
M
Memory .................................................................... 5
Mounting ................................................................ 20
bolting considerations ......................................... 20
panel or wall mount
pole mount
N
Non-Sparking
ATEX Zone 2 certification notes ......................... 111
O
Opening the enclosure ............................................ 19
Operation ............................................................... 81
O-rings .................................................................... 23
P
Physical Security ..................................................... 10