Emerson Fisher 630 Series - Page 9

630 Series
9
Key Description Part Number
1 Adjusting Screw, Steel See Table 4
2 Hex Nut, plated steel 1A352424122
3 Spring Case
Low-pressure
Cast iron 3C780919042
Steel 3N698122012
High-pressure
Cast iron 3C780819042
Steel 3N698322012
4 Upper Spring Seat, Zinc
Pressure range to 275 psig / 19.0 bar 16A9812X012
Pressure range over 275 psig / 19.0 bar 16A9813X012
5 Spring, steel See Table 5
6 Cap Screw, plated steel 1R817699012
7 Lower Spring Seat
Low-pressure, Steel 0W020324102
High-pressure, Zinc
Pressure range to 275 psig / 19.0 bar 0W020144022
Pressure range over 275 psig / 19.0 bar 1K371044022
8 Diaphragm Plate, Zinc-plated steel
Low-Pressure only (1 required) 0W020225072
9 Cap Screw, Zinc-plated steel
For use with steel diaphragm adaptor
For low-pressure regulator (10 required) 1C379124052
For high-pressure regulator (4 required) 1B787724052
10 Cap Screw, plated steel (for use with
cast iron diaphragm adaptor)
Low-pressure (10 required) 1A352524052
High-pressure (4 required) 1A352524052
11* Diaphragm
Neoprene (CR)
For low-pressure regulator 0W020002192
For high-pressure regulator 0W019902192
Fluorocarbon (FKM)
For low-pressure regulator (2 required) 0W0200X0022
For high-pressure regulator (2 required) 0W019902402
12 Connector Head Assembly
Aluminum trim 16A9811X012
Aluminum trim (NACE) 16A9811X032
Stainless steel trim 1P8465000B2
Stainless steel trim (NACE) 1P8465X0012
13 Diaphragm Adaptor
Low-pressure
Cast iron 0W019719012
Steel 2N698522012
Steel (NACE) 2N6985X0072
High-pressure
Cast iron 0W019819012
Steel 2N698722012
Steel (NACE) 2N6987X0042
14 Lever Assembly, Steel or Stainless steel
Low-pressure 1B2891000A2
Low-pressure (NACE) 1B2891X0032
High-pressure 1B2890000A2
High-pressure (NACE) 1B2890X0022
Key Description Part Number
15 Pin
Stainless steel 0W018835172
Stainless steel (NACE) 0W0188X0022
16* Gasket, Composition 0W018704022
17 Cap Screw, steel (4 required)
1 in. / DN 25 body 1A935924052
2 in. / DN 50 body 11A7202X022
18 Inlet Adaptor, Steel
Body
Cast Iron
1 NPT 1F479823022
2 NPT 1F479923022
Steel
1 NPT 1F479823022
1 NPT (NACE) 1F4798X0022
2 NPT 1F479923022
2 NPT (NACE) 1F4799X0022
CL150 RF
1 in. / DN 25 12A3803X012
2 in. / DN 50 27B0495X012
2 in. / DN 50 (Type 630R only) 28B6247X012
CL300 RF
1 in. / DN 25 12A3633X012
2 in. / DN 50 27B0488X012
2 in. / DN 50 (Type 630R only) 28B6248X012
CL600 RF
1 in. / DN 25 18A7701X012
2 in. / DN 50 27B0498X012
2 in. / DN 50 (Type 630R only) 28B6249X012
19* Inlet Body Gasket (2 required)
Copper, for Brass trim 0W018415042
Composition, for Stainless steel trim 0W018404022
20* Orice
Type 630
Brass
1/8 in. / 3.18 mm 0Z040014012
3/16 in. / 4.76 mm 1B219514012
1/4 in. / 6.35 mm 0W018314012
3/8 in. / 9.53 mm 0W018214012
1/2 in. / 12.7 mm 0W018114012
Stainless steel
1/8 in. / 3.18 mm 1K416635032
3/16 in. / 4.76 mm 1K416535032
1/4 in. / 6.35 mm 1K416435032
3/8 in. / 9.53 mm 1K416335032
1/2 in. / 12.7 mm 1K416235032
Stainless steel (NACE)
1/8 in. / 3.18 mm 1K4166X0012
3/16 in. / 4.76 mm 1K4165X0012
1/4 in. / 6.35 mm 1K4164X0012
3/8 in. / 9.53 mm 1K4163X0012
1/2 in. / 12.7 mm 1K4162X0012
Type 630R
Brass
1/2 in. / 12.7 mm 1B735014012
Stainless steel
1/2 in. / 12.7 mm 1B735035032
Stainless steel (NACE)
1/2 in. / 12.7 mm 1K4162X0012
*Recommended spare part.