EasyManua.ls Logo

Emerson Fisher LCP100 - User Manual

Emerson Fisher LCP100
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.Fisher.com
Fisher
™
LCP100 Local Control Panel
Contents
Introduction 1.................................
Scope of Manual 1.............................
Description 2.................................
Specifications 2...............................
Educational Services 2...........................
Installation 5..................................
Hazardous Area Classifications and Special
Instructions for “Safe Use” and Installation
in Hazardous Areas 5........................
Mounting 5..................................
Electrical Connections 5........................
Pre‐Setup Testing 24............................
Setup 25......................................
Principle of Operation 25........................
Maintenance 26................................
Troubleshooting 26............................
Parts Ordering 27...............................
Parts List 27...................................
Common Parts 27.............................
Figure 1. Fisher LCP100 Local Control Panel, with
FIELDVUE DVC6200 SIS Digital Valve Controller
and Bettis
™
Actuator
X0247
Introduction
Scope of Manual
This instruction manual includes installation and maintenance information for the Fisher LCP100 local control panel
(figure 1). This device is used with Fisher FIELDVUE™ instruments in Safety Instrumented Systems (SIS). Refer to the
DVC6200 SIS Digital Valve Controllers for Safety Instrumented System (SIS) Solutions instruction manual
(D103557X012
) or the DVC6000 SIS Digital Valve Controllers for Safety Instrumented System (SIS) Solutions
instruction manual (D103230X012
) for additional information.
Unless otherwise noted, the information in this instruction manual applies to both DVC6200 SIS and DVC6000 SIS
digital valve controllers. For simplicity, the DVC6200 SIS model name will be used throughout.
Instruction Manual
D103272X012
LCP100 Local Control Panel
August 2017

Table of Contents

Questions and Answers

  • L
    lisalopezJul 31, 2025
    What to do if lights are not lit on Emerson Fisher LCP100?
    • M
      Michael TorresJul 31, 2025
      If the lights on your Emerson Control Panel are not lit, several issues could be the cause. First, ensure the LCP100 is properly connected to the digital valve controller aux terminal, as described in the installation section. Next, verify that the power switch is correctly set; if using Loop Power, the switch should be set to Loop Power, not 24 VDC, and vice versa. Also, the Loop Power option requires 8 mA current to operate, so ensure sufficient current is available. Finally, the LED itself may be damaged and require replacement.
  • J
    joserodriguezAug 4, 2025
    What to do if the lights are blinking on my Emerson Fisher LCP100 Control Panel?
    • S
      Samuel ToddAug 4, 2025
      If the lights are blinking on your Emerson Control Panel, it indicates that the valve is not at its normal stop. Check for proper calibration and re-run the calibration if necessary.
  • J
    Jason YoungAug 8, 2025
    How to fix Emerson Fisher LCP100 Control Panel lights that are not lit?
    • E
      elijahharperAug 9, 2025
      If the lights on your Emerson Control Panel are not lit, it might be due to improper connection of the LCP100 to the digital valve controller aux. terminal. Ensure that the LCP100 is correctly connected to the digital valve controller aux. terminal, as described in the Installation section.
  • K
    Katherine ParsonsAug 13, 2025
    Why are the lights not lit on my Emerson Fisher LCP100 Control Panel even though the LCP100 is connected?
    • G
      George BallAug 13, 2025
      If the LCP100 is properly connected to the digital valve controller aux terminal, but the lights are still not lit on your Emerson Control Panel, the power switch might not be set correctly. Ensure that the power switch is set correctly. If Loop Power is used, ensure that the switch position is set to Loop Power, and NOT 24 VDC, and vice versa.
  • A
    Ashley ClarkAug 17, 2025
    What to do if the Emerson Fisher LCP100 Control Panel lights are not lit, even when the power switch is correctly set?
    • B
      bbatesAug 17, 2025
      If the power switch is set correctly, but the lights are still not lit on your Emerson Control Panel, and the Loop Power option is selected, it could be due to insufficient current. The Loop Power Option requires 8 mA current to operate. Ensure that there is sufficient current.
  • D
    David JacksonAug 21, 2025
    Why are the lights still blinking on my Emerson Control Panel after calibration?
    • C
      Christine MayAug 21, 2025
      If the lights are still blinking on your Emerson Control Panel after proper calibration, the Hi Hi / Lo Lo alerts settings might not be correctly set. Ensure that the Hi Hi / Lo Lo Alert settings are 99 and 1% respectively. For large rotary valve, adjust settings to 98 and 2% and observe.
  • K
    Kevin NicholsAug 26, 2025
    What to do if Emerson Fisher LCP100 Control Panel lights are not lit after checking connections and current?
    • K
      Kimberly GravesAug 26, 2025
      If the LCP100 and the digital valve controller are properly connected, and there is sufficient current, but the lights are still not lit on your Emerson Control Panel, the LED may be damaged. Replace the LED.

Summary

Introduction

Scope of Manual

Details the scope and purpose of this instruction manual for the Fisher LCP100 local control panel.

Description

Provides a description of the LCP100 local control panel and its functions.

Specifications

Electrical Classification

Details the electrical classification ratings for the LCP100 panel.

Electromagnetic Interference (EMI)

Covers the EMI performance criteria and standards met by the LCP100.

Installation

Hazardous Area Classifications and Installation Instructions

Details hazardous area classifications and special safety instructions for installation.

Mounting

Provides information on the mounting of the LCP100 local control panel and orientation requirements.

Electrical Connections

Explains the electrical connection requirements and warnings for the LCP100 local control panel.

Pre-Setup Testing

Successful Partial Stroke Test

Details the procedure for a successful partial stroke test on the LCP100.

Emergency Demand Testing

Explains emergency demand tests via logic solver and local control panel.

Setup

Device Setup via Field Communicator

Instructions for configuring the LCP100 using a 475 Field Communicator.

Principle of Operation

Maintenance and Troubleshooting

Instrument Troubleshooting

Guidance on troubleshooting common issues with the LCP100 control panel.

Parts Information

Parts Ordering

Information on how to order parts for the LCP100, including serial number and contact details.

Parts Kits and List

Details available parts kits and common parts for the LCP100, referencing figures.

Emerson Fisher LCP100 Specifications

General IconGeneral
CategoryControl Panel
ManufacturerEmerson
ModelFisher LCP100
DisplayLCD
Input Voltage24 VDC
Communication ProtocolsHART, Foundation Fieldbus, Profibus
MountingPanel Mount
Enclosure RatingNEMA 4X

Related product manuals