EMTEST PFM 200N100.1 - User Manual

User’s Guide
PFM 200N100.1
Voltage Dips and Drops Interruptions
- E-10 Brief Voltage Drop
- E-13 Dropout Pin
- E-14 Dropout Connector
The PFM 200N100.1 has been specially engineered for
performing dropout pulses on battery and signal lines.
The PFM 200N100.1 contains a switch for battery voltage as
well as an additional switches for battery return lines from 100
mA to 100 A. An additional set of 16 switches are provided for
data and signal line switching from
100 μA to 2 A.
BMW QV65013
GMW3172
LV 124 (2013)
LV 148
Renault 36-00-808/--M
Nissan 28401 NDS02
Version:
1.12 / 26.02.2016
emc test equipment
Replaces:
1.11 / 16.10.2015
File Name:
UserManual-PFM200N100.1-E-V1.12.doc
Print Date:
26.02.16

Summary

Safety Information for the PFM 200 N100.1

PFM 200 N100.1 Safety Instructions and Precautions

Covers essential safety guidelines, device symbols, power connection, earthing, and cable usage.

Safe Testing Procedures and DUT Protection

Details crucial precautions for safe testing, including switching off procedures, DUT protection, and input capacitance.

PFM 200 N100.1 Dropout Simulator

PFM 200 N100.1 Battery Voltage Switch (S1 P)

Details the power switch (S1P) for battery voltage, its specifications, and capabilities.

PFM 200 N100.1 Data and Signal Line Switches (S1-S16)

Describes the switches (S1-S16) for data and signal lines, their specifications, and usage.

Testing According to LV 124 and LV 148 Using AutoWave.control

Locating LV 124 & LV 148 Tests in AutoWave.control

Guides users on how to find and select LV 124 and LV 148 standard tests within the AutoWave.control software.

PFM 200 N100.1 Switch Settings in AutoWave.control

Details the software settings for the PFM 200N100.1 switches, including S1 and discharge switches S2-S5, for dropout testing.

E-10 Short Interrupts According to LV 124 (2013-02)

E-10 Test Case 1: Power Interruption (S1 Switched, S2 Open)

Simulates power supply interruption with S2 open, detailing testing procedures with AutoWave.control software.

E-10 Test Case 2: Severe Interruption (S1;S2 Switched)

Simulates a severe interruption where S2 discharges the DUT quickly, and outlines testing with AutoWave.control.

E-10 Reference Measurements for Edge Steepness

E-13 Pin Interruption according to LV 124 (2013-02)

E-13 Test Case 1: Slow Interval

Simulates slow pin interruptions by disconnecting and reconnecting for 10 seconds, detailing data line testing with AutoWave.

E-13 Test Case 2: Burst of Interruptions

Simulates intermittent contact by generating bursts of interruptions on each pin, detailing data line testing with AutoWave.

E-13 Reference Measurements for Data Lines

E-14 Connector Interruption

E-14 Connector Interruption Tests on Battery Lines

E-14 Connector Interruption Tests on Data Lines

Technical Data for the PFM 200 N100.1

PFM 200 N100.1 Power Line Switch Technical Data

PFM 200 N100.1 Signal;Data Line Switch Technical Data

Accessories for LV 124

CA LV124 Calibration Loads for E-10 & E-13 Tests

EMTEST PFM 200N100.1 Specifications

General

Brand	EMTEST
Model	PFM 200N100.1
Category	Test Equipment
Language	English