Enapter Electrolyser Quick Start Guide

Quick Start Guide
1
Download the Owner’s Manual
Electrolyse
EL 4.0
Enapter makes dierent versions of
electrolyser based on your needs.
Electrolysers come in AC/D
or DC/DC versions as well as air-
cooled or liquid-cooled versions (LC).
All informaon about Enapter devices can be
found at handbook.enapter.com
Contact support at support@enapter.com.
For indoo
use only
For humid environments
addional IP68 protecon
required
Check all parts for
damage regularl
Device out-of-the-box comes in Maintenance mode
Yellow LED should be steady. Do not leave it turned on and
unaended for a long me.
Follow Installaon Instrucons i
the Owner’s Manual
2
Insert the two supplied j umpers into the Dry Con. port
in the 3 rd and 4th posions on the front panel of the
EL. If you want/need to implement a safety chain ,
please refer to Dry Contact Connecon G uide in the
owner ' s manual.
Plug the power cable into the P ower port
and switch the power on.
AC – protecve earth on the le , live on the right 
DC – posive on the top.
Screw supplied antenna to the Ant. port.
Dry Con.
2
1
3
4
G N L
Y ou must follow owner ' s manual for all steps , including
pipe and wire connecon , operaon , transportaon ,
storage and disposal.
3 W ater Inlet R e q uirements
H2 O I N port is used for automac re  lling from connected
demineralised water source during normal operaon ,  rst re  lling
and maintenance. During hydrogen producon water consumpon
rate is around 400 mL/hr.
С onnect electrolyser to water suppl 
only through water puri  caon system
according to the O wner ’ s M anual. W ater
conducvity must be < 2 0 µ S/cm (at
2 5° C) and pressure between of 1- 4 bar.
H2 O I N
P roper inlet water source must be connected before
proceeding to the next steps.
Flush all water pipes with demineralised water before
connecng your device to ensure nothing is stuck in the lines.
4 Check H2 V ent and O 2 V ent Lines
It is the installer ' s responsibility to regularly check and maintai 
H2 V E N T and O 2 V E N T lines , as well as keeping the lines free of ice
and any obstrucons.
M ake sure there is no
obstrucon into the H2 V E N T
line. T his can cause irreparable
damage to your hydrogen
system
H2 V E N T
O 2 V E N T
N o blockage should be present
on O 2 V E N T on the user side of
the interface.
DO N O T connect H2 V E N T line with O 2 V E N T line
Mixing these outputs is extremely dangerous.
Always check H2 vent and O 2 vent lines for blockage and
damage.
U se Enapter W ater T ank to solve the problem of
unstable water supply. It can be  lled manually with
prepared demineralised water as well as directly
connected to water source.
Enapter W ater tank deliveries pressure up to 2. 7 5 bar.
W ater conducvity must be < 2 0 µ S/cm (at 2 5° C).
External Enapter W ater T ankOponal
Ant.
Cooling W ater ports (normally closed) are used for cooling the system
using water or a water glycol mi x ture. Check the manual to guarantee the
opmal temperature as a funcon of your  ow rate and ambient
temperature.
T he required  ow rate is 1-2 L/min and input pressure can ' t e x ceed 4 bar.
M ake sure you are not reversing the I N and the O UT .
Cooling Loop R e q uirementEL4.0 LC version
Guide version 1.1

Enapter Electrolyser Specifications

General

Brand	Enapter
Model	Electrolyser
Category	Transformer
Language	English