INSTALLATION INSTRUCTIONS
-02- -03--01-
DESCRIPTION
FEATURES
ZWN-RSM2
Range...................................................................Up to 150 feet line of sight
SPECIFICATIONS
between the Wireless Controller and the closest Z-Wave receiver module.
INSTALLATION
Wiring Diagram:
WARNINGS AND CAUTIONS
To be installed and/or used in accordance with appropriate electrical codes
and regulations. Exercise extreme caution when using Z-Wave devices to
control appliances. Operation of the Z-Wave device may be in a different
room than the controlled appliance, also an unintentional activation may
occur if the wrong button on the remote is pressed. Z-Wave devices may
automatically be powered on due to timed event programming.Depending
upon the appliance, these unattended or unintentional operations could
possibly result in a hazardous situation.
Z-Wave enabled devices should never be used to supply power to, or
control, the On/Off status of medical and/or life support equipment.
If you are unsure or uncomfortable about performing the installation,
please consult a qualified electrician.
8. Attach the wall plate.
9. Restore power at the circuit breaker and test the system.
, then wire existing switches.
1. WARNING: To avoid fire, shock, or death. Turn off power at circuit breaker
or fuse and test that power is off before wiring.
2. Remove wall plate and switch mounting screws.
3. Carefully remove existing switches from the switch box.
4. Disconnect the wiring from existing switches.
5. Connect the ZWN-RSM2 module as shown in the wiring diagram.(Figure 1)
6. Check connections to be sure they are tight and no bare conductors are exposed.
7. Insert the ZWN-RSM2 module into the box first
Operating Temperature..............................................................32° F-104° F
Smart Dual Relay Switch Module
Maximum Load requirement.................................................................4A×2
Voltage.........................................................................120-277VAC, 50/60Hz
Z-Wave Frequency.............................................................. 908.42MHz(US)
Size.................................................................................1.63'' ×1.63'' ×0.82''
Please consult an electrician if you have trouble identifying the type of wiring
circuit you wish to convert or if you do not feel confident in your ability to
convert the circuit to Z-Wave control.
Works with existing light switches, neutral wire required
Slim size module with built
in Z-Wave Plus technology
Acts as a Z-Wave repeater to extend the range
On/Off control via Z-Wave controller, manual wall switch
Z-Wave unifies all of your home electronics into an integrated wireless
network and helps them communicate with each other. Any Z-Wave enabled
item can be added to the network, making your home electronics fully
compatible.
The ZWN-RSM2 Switch Module is a component of a lighting control system
used to turn an existing switch into a Z-Wave
switch. This ZWN-RSM2
module is a Z-Wave enabled device and is fully
compatible with any Z-
Wave enabled network. In the Z-Wave network, this
device is designed to act
as a wireless repeater. Once the ZWN-RSM2 module
is installed and
configured, it will retransmit the RF signal from one
device to another until the
intended device is reached. This ensures that the
signal is received by its
intended destination by routing the signal around obstacles and radio dead
spots.
Basic Operation
OPERATIONS
The connected device can be turned ON in two ways:
2. Z-Wave remote controller.
1. Manual control with the button on the connected switch.
TIPS FOR ARRANGING THE ANTENNA:
Position the antenna as far from metal elements as possible
to prevent
interferences.
Metal surfaces in the direct vicinity of the antenna
may impair signal
reception.
Do not cut or shorten the antenna - its length is perfectly matched.
Manual Control
Manually turn on/off connected appliances the same way as you would with a
traditional switch.
Remote Control
When the ZWN-RSM2 switch module is included in a Z-Wave network, it can be
turned on/off remotely by a portable controller or a Z-Wave enabled gateway
controller.
Z-Wave network inclusion/exclusion
For controller inclusion/exclusion mode, please refer to the user manual of the
controller.
Press and release the program button (Figure 3) on the ZWN-RSM2 module to
enter learning mode. Toggling the manual switch that is wired to the Aux1 line (not
Aux2 line) will also set the module to learning mode for one second. The module
should now be included into the network. If the Z-Wave network failed to add ZWN-
RSM2, please try exclusion first.
ZWN-RSM2
PLUS
Neutral
(White)
Neutral
Aux 2
Line
Switch 2
Aux 1
Line
Switch 1
Hot
Line
(Black)
Load 2
Neutral
Load 1
Neutral
ZWN-RSM2
Program Button
Antenna
ZWN-RSM2
Figure 1
Figure 2
Figure 3
To Next Page
Need help?
General
