The EnfaSafe Freedom 360 Rotate is a versatile child restraint system designed for use in vehicles, accommodating children from birth up to 12 years of age, or weighing between 0-36 kg. This car seat is approved under standard ECE 44 04, ensuring its safety and compliance with European regulations.
Function Description:
The EnfaSafe Freedom 360 Rotate functions as a multi-group child car seat, adapting to a child's growth through various stages:
- Group 0+ (0-13kg): Rear-facing installation using ISOFIX, top tether, and the integrated 5-point harness.
- Group I (9-18kg): Can be installed either rear-facing or forward-facing, both using ISOFIX, top tether, and the integrated 5-point harness.
- Group II, III (15-36kg): Forward-facing installation, offering two options:
- Using ISOFIX and the vehicle's 3-point seat belt.
- Using only the vehicle's 3-point seat belt.
The "360 Rotate" feature allows the seat to be easily turned for rear-facing or forward-facing positions, and also facilitates a loading position to make placing and securing the child easier.
Important Technical Specifications:
- Weight Range: 0-36 kg
- Age Range: 0-12 years (approximately)
- Approval Standard: ECE 44 04
- Installation Methods:
- ISOFIX + Top Tether + 5-point harness (Groups 0+, I)
- ISOFIX + 3-point vehicle seat belt (Groups II, III)
- 3-point vehicle seat belt only (Groups II, III)
- ISOFIX Categories: Approved for ISOFIX category D (0-13 kg) and B1 (9-18 kg). Users should check their vehicle's manual for compatibility.
- Recline Positions:
- Rear-facing (0-18kg): Position 1 only.
- Forward-facing (9-36kg): Positions 1, 2, 3, 4 are allowed.
Usage Features:
- Rotation Button (13): Allows easy rotation of the seat between rear-facing, forward-facing, and loading positions.
- ISOFIX System (6): Provides a secure and stable installation in vehicles equipped with ISOFIX anchor points. The ISOFIX anchors can be extended to their maximum length using the level (18). A display window (17) turns from red to green to confirm correct ISOFIX connection. Plastic guides are provided for vehicles without built-in guides.
- Top Tether (4): An additional anchor point for enhanced stability, particularly important for rear-facing and forward-facing installations with the harness. It connects to an anchor point in the vehicle, and its strap should be tightened until a green signal is displayed on its indicator.
- 5-Point Harness (9): Used for Group 0+ and Group I children. It features a tensor adjusting button (10) and strap (11) for tightening, and a buckle (5) with a red release button. The harness straps should be adjusted to fit snugly and not be twisted.
- Headrest Adjustment (1, 7): The headrest (1) can be adjusted using the handle (7) to ensure the shoulder harness comes out approximately 1cm above the child's shoulders.
- Reclining Button (12): Allows adjustment of the seat's recline position.
- Insert Cushion:
- Complete insert cushion is used until the baby reaches 5kg.
- The inner headrest is removed when the baby is 5-12kg.
- The complete insert cushion is removed when the child is 12-36kg.
- Harness Storage: Once the child reaches 18kg, the 5-point harness should be stored away. This involves loosening the harness, removing side cushions, undoing press studs, hiding shoulder pads, removing buckle padding, threading the buckle through the cover and under the cushion, and storing buckle parts in a compartment under the cushion. The cover is then fixed back on the seat.
- Belt Guides (8, 15): For Group II and III children using the vehicle's 3-point seat belt, the shoulder belt is threaded through the upper belt guide (8) and the lap belt through the lower belt guide (15).
- Safety Warnings:
- Never leave a child unattended in the vehicle.
- Replace the car seat after an accident, even if no visible damage.
- Do not travel for more than 2 hours without a break, especially for babies.
- Do not use the seat without its textile cover and harness pads.
- Ensure all straps are tight, adjusted to the child's body, and not twisted.
- Ensure the lap strap is worn low down to firmly engage the pelvis.
- Do not alter the product or add/remove accessories without authorization.
- Do not use on a passenger seat with an activated frontal airbag.
Maintenance Features:
- Cover Removal: The textile cover is easily removable. It has 2 fastening points on the front and plastic parts on the sides. Unfasten these points and gently pull to remove.
- Cleaning: The cover can be machine washed with mild detergent at a maximum temperature of 30°C. Refer to the care label for specific washing instructions. Do not tumble dry. Avoid prolonged exposure of upholstery to direct sunlight when not in use. Plastic parts can be cleaned with a damp cloth and neutral detergent.
- Storage: Keep the instruction manual for future reference, ideally in the compartment at the back of the car seat shell. Ensure all luggage and objects in the vehicle are secured to prevent injury in case of an accident.
For further assistance, users can contact Euroactive HK. LTD. via phone at +353 1 2952111 or email at reachout@euroactiveproducts.com. The company has offices in Dublin, Ireland, and London, United Kingdom. The product is made in China.
Need help?
General
To Next Page