Need help?Do you have a question about the Engl SOVEREIGN 100 and is the answer not in the manual?
General| Power Output | 100 Watts |
|---|---|
| Channels | 4 |
| Preamp Tubes | 4 x ECC83 / 12AX7 |
| Power Tubes | 4 x EL34 |
| Footswitchable Channels | Yes |
| Type | Tube Amplifier |
| Effects Loop | Yes |
| Speaker Outputs | 2 x 4 ohms, 2 x 8 ohms, 1 x 16 ohms |
1/4" unbalanced input for guitar signal.
Adjusts preamp input sensitivity for the Clean channel.
Sets preamp input sensitivity and distortion for the Crunch channel.
Boosts upper end of Clean and Crunch channels for brighter tone.
Bass, Middle, and Treble controls for Clean/Crunch channels.
Dedicated high-frequency EQ for Clean and Crunch channels.
Clean Volume and Crunch Volume controls.
Buttons for selecting main channels (1/2) and sub channels (I/II).
Controls for FX loops and onboard spring reverb system.
Stores or duplicates MIDI presets.
Master A, Master B, and Master A/B switching.
Controls for power amp standby and mains power on/off.
Sets input sensitivity and preamp saturation for Lead I channel.
Sets input sensitivity and preamp saturation for Lead II channel.
Selects between Soft Lead and Heavy Lead gain modes.
Bass, Middle, Treble, and Presence controls for Lead channels.
Lead I Volume and Lead II Volume controls.
Power cord input and main fuse compartment.
MIDI IN and MIDI THRU DIN connectors for system integration.
Selector for powering ENGL MIDI foot boards.
Configures MIDI channel and Master Volume Mute function.
Connects Custom ENGL Z-9 Footswitch for remote amp control.
Connects conventional footswitches for channel switching.
SEND, RETURN, and BALANCE controls for FX Loop 1.
SEND, RETURN, and BALANCE controls for FX Loop 2.
Intensity knobs for Reverb on Channel 1 and Channel 2.
Adjusts the output level for the frequency-compensated line out.
Selects line out source and handles XLR ground lift.
Frequency-compensated, balanced XLR output for mixers/recorders.
Speaker output for 4-ohm cabinets.
Speaker output for 8-ohm cabinets.
Speaker output for 16-ohm cabinets.
Configurations for the 1x12" combo with external cabinets.
Configurations for the 2x12" combo with external cabinets.
Options for connecting external cabinets to both combo models.
Designer's notes on Clean, Crunch, Lead I, and Lead II channel voicing.
Explanation and tips for using the Noise Gate.
Details on protection systems like Power Tube Monitoring.
Step-by-step guide for writing and copying MIDI presets.
Guidelines for safely transporting and maintaining the amplifier.
Definitions for MIDI-Preset, MIDI Channel, and MIDI-Volume Mute.
Indicates memory errors and no speaker connection.
Shows when settings are edited or copy process is active.
Alerts to issues with individual power tubes V1-V4.
Addresses problems with programmable features and MIDI response.
Diagnoses issues like no output signal or humming noises.
Deals with power amp protection trips and cooling fan operation notes.
Output power, input levels, power consumption, fuses, tubes, logic system, memory, interfaces.
Details cooling system, dimensions, and weight of the amplifier.
Diagram and description of tube placement and their roles.
Wiring details for XLR Line Out and DIN MIDI IN connectors.
Wiring for Serial Amp Control and Dual Footswitch ports.
Connecting ENGL Z-12/Z-15 MIDI foot boards.
Connecting the ENGL Z-9 via Serial Amp Port or MIDI IN.
Connecting standard footswitches via the Z-4 jack.
To Next Page
