England's Stove Works 55-SHPEP User Manual (English)

Questions and Answers:

T
terri74Sep 1, 2025
What to do if my England's Stove Works Pellet stove displays an "E?3" code?
- M
  Madison KempSep 1, 2025
  If your England's Stove Works Pellet stove is showing an "E?3" code, this can be caused by: 1. Convection (Room Air) blower failure: Check the convection blower for proper function and replace it if necessary. 2. Partially blocked flue: Check the flue for any obstructions. 3. Using fuel other than premium wood pellets: Ensure you are ONLY using premium wood pellets in this stove.
C
Cassandra GrantAug 30, 2025
Why is the auger not turning on my England's Stove Works Pellet stove?
- A
  Andrew LopezAug 30, 2025
  If the auger is not turning on your England's Stove Works Pellet stove, it could be due to several reasons. A bad auger motor could be the cause, in which case you should replace it. Another possibility is that foreign matter is jamming the auger; remove the pellets and any obstructing object. It may also be a vacuum sensor issue, so check the exhaust blower.
T
Trevor SchmittAug 29, 2025
What to do if my England's Stove Works Pellet stove displays an "E?4" code?
- B
  bryan71Aug 29, 2025
  If your England's Stove Works Pellet stove displays an "E?4" code (Proof of flame lost), it could be due to several reasons: * The hopper is empty. Refill it with pellets and restart the stove. * The hopper lid was left open for too long during refueling. Keep the lid open for the shortest time possible. * Component failure. An auger motor or combustion motor failure might be the cause. * Blower speed is set too high, cooling the firebox too rapidly. Operate the stove with the blower speed and heat range at the same value.
J
Joshua BenjaminAug 27, 2025
Why won't the room blower operate on my England's Stove Works Pellet stove?
- Z
  Zachary BenderAug 28, 2025
  If the room blower isn't operating on your England's Stove Works Pellet stove, it could be due to a loose thermal sensor. Try tightening the connection on the sensor. Another cause might be that the blower speed is set higher than the heat range, causing the stove to cool and the blower to cycle. If so, lower the blower speed. A loose connection on the control board could also be the problem; check the control board connection.
C
Charles FlynnAug 27, 2025
What does "E?2" code on England's Stove Works Pellet stove control board mean and why unit shuts down in 15-20 minutes?
- M
  Michael BassAug 27, 2025
  If your England's Stove Works Pellet stove shuts down in 15-20 minutes with an "E?2" code, it could be due to a loose thermal sensor; check both sides of the thermal sensor connection (at exhaust blower and at control board). Another cause might be the control board settings; start the stove on minimum Heat Range 5 to ensure a good fire is started. Lastly, it could be a failure to light pellets; check the igniter for buildup or failure.
J
Jason JosephAug 25, 2025
What does "E?3" code on my England's Stove Works 55-SHPEP control board mean?
- C
  Charles PatelAug 26, 2025
  An "E?3" code on your England's Stove Works Pellet stove control board indicates a convection (room air) blower failure. Check the convection blower for proper function and replace it if necessary. This code can also mean partially blocked flue, so check the flue for obstructions. Finally, using fuel other than premium wood pellets can trigger this code, so use ONLY premium wood pellets in this stove.
R
Rebecca ArmstrongAug 23, 2025
What to do if my England's Stove Works 55-SHPEP displays an "E?4" code (proof of flame lost)?
- S
  suttonandreaAug 23, 2025
  If your England's Stove Works Pellet stove shows an "E?4" code, indicating a loss of flame, it could be due to several reasons. The hopper might be empty, so refill it with pellets and restart the stove. Also, ensure you keep the hopper lid open for the shortest time possible when refueling. Component failure, such as an auger motor or combustion motor issue, can also cause this code. Lastly, the blower speed might be set too high, cooling the firebox too rapidly; operate the stove with the blower speed and heat range at the same value.