Envirotec ET64H - User Manual

Questions and Answers

K
Kimberly MarquezAug 8, 2025
What to do if there is excessive water in brine tank of Envirotec Water Dispenser?
- I
  imoyerAug 8, 2025
  If you notice excessive water in the brine tank of your Envirotec Water Dispenser, it could be due to several reasons: 1. The drain line flow control might be plugged. Try cleaning it and then put the system through a manual regeneration cycle. 2. The injector system could be plugged. Clean the injector and screen. 3. The timer may not be cycling. Consider replacing it. 4. There might be foreign material in the brine valve. Replace the brine valve seat and clean the valve. 5. Foreign material could be in the brine line flow control. Clean the brine line flow control. 6. There might have been a power loss during brine fill. Check the power source.
T
Tracey JimenezAug 13, 2025
How to fix loss of water pressure in Envirotec Water Dispenser?
- L
  Lisa Gonzalez DVMAug 13, 2025
  If you are experiencing a loss of water pressure with your Envirotec Water Dispenser, consider the following: * Iron build-up might be present in the water softener. Clean the control, add resin cleaner, and increase the regeneration frequency and/or backwash time. * The inlet of the control could be plugged. Remove the piston and clean the control of any foreign material. * The resin might be fouled. In this case, replace the resin.
R
Rodney RomeroAug 17, 2025
Why Envirotec ET64H uses too much salt?
- D
  Daniel RomanAug 17, 2025
  If your Envirotec Water Dispenser is using too much salt, check the salt usage and salt setting. Also, excessive water in the brine tank could be the cause. This means the brine draw isn't functioning correctly, so clean or replace the injectors.
L
larrywilkinsonAug 21, 2025
What causes loss of resin media through drain line in Envirotec Water Dispenser?
- L
  Lisa FrankAug 21, 2025
  If you're experiencing loss of resin media through the drain line of your Envirotec Water Dispenser, it could be due to: * Air in the water system. Make sure your well system has a proper air eliminator control and check for a dry well condition. * The drain line flow control being too large. Check to ensure the drain line flow control is sized properly for your mineral tank.
A
andrewprestonAug 26, 2025
What to do if Envirotec ET64H Water Dispenser fails to regenerate?
- L
  Lisa ChanAug 26, 2025
  If your Envirotec Water Dispenser isn't regenerating, it might be due to a couple of reasons. First, check that the unit has permanent electrical service by checking the fuse and outlet. Ensure the plug isn't in a switched outlet. Second, the timer could be defective and need replacement.
R
Roberta NewtonAug 29, 2025
How to remove iron from softened water in Envirotec ET64H Water Dispenser?
- T
  Terry WyattAug 29, 2025
  If you find iron in the softened water from your Envirotec Water Dispenser, it's likely the resin bed is iron fouled. To address this, add a resin cleaner and increase the frequency of regeneration.
C
Cole CarsonNov 3, 2025
Why is my Envirotec ET64H not softening water?
- J
  Juan HinesNov 3, 2025
  If your Envirotec Water Dispenser isn't softening water, here are a few things to check: * Ensure the bypass valve is in the service position. * Make sure there's enough salt in the brine tank, above the water level. Wait an hour, then manually regenerate. * The injector screen may be plugged and require cleaning. * Check if enough water is flowing into the brine tank. If not, check the brine tank fill time and clean the brine line flow control if it's plugged. * Consider replacing seals, spacers, piston, or distributor if there's an internal valve leak. * If the hot water is hard, use enough hot water to turn over the tank with soft water. * Inspect the distributor tube for cracks and check the O-ring and tube pilot for leaks at the distributor tube. * If the system isn't...