How to fix Epson 11880 - Stylus Pro Color Inkjet when cannot configure network interface or print from network?
If you're unable to configure the network interface or print from the network with your Epson Printer, the printer or network settings may be incorrect. First, check if you can print a status sheet. If the status sheet prints successfully, then examine the network settings.
What to do if Model Name and IP Address do not appear in the EpsonNet Config dialog box on Epson Printer?
If the Model Name and IP Address are missing in the EpsonNet Config dialog box, it might be because a valid IP address hasn't been set. To resolve this, set a valid IP address. Then, refresh the status by selecting Refresh from the View menu. You can also increase the timeout duration by going to Options from the Tool menu and selecting Timeout; however, be aware that this may slow down EpsonNet Config.
What to do if EpsonNet Config cannot be used because no network is installed on Epson Printer?
If you receive the message “EpsonNet Config cannot be used because no network is installed” when starting EpsonNet Config, it means that TCP/IP is not installed on your computer or its IP address is not set correctly. To fix this, install the TCP/IP protocol or set a correct IP address for your computer.
Why cannot I print even if I have assigned the IP address to the computer and the Epson 11880 - Stylus Pro Color Inkjet Printer?
If you cannot print even after assigning an IP address to both your computer and Epson printer, it could be because you assigned the computer's IP address manually, while the printer's IP address was assigned through Automatic Private IP Addressing (APIPA). To resolve this, assign the printer’s IP address so that it belongs to the same segment as the computer, using EpsonNet Config and the printer’s control panel.
What to do if the message 'Could not complete communicating configuration data' appears when sending settings to the network interface of Epson 11880 - Stylus Pro Color Inkjet Printer?
If you see the message “Could not complete communicating configuration data” when sending settings to the network interface, especially when using a dial-up router, run Command Prompt on the computer with EpsonNet Config installed. Then, enter the command: >ROUTE_ADD_the IP address of the network interface_ the IP address of the computer. For example: >ROUTE ADD 192.168.192.168 22.33.44.55.
How to fix unable to start EpsonNet Config on Epson 11880 - Stylus Pro Color Inkjet?
If you're unable to start EpsonNet Config, it might be because you added or deleted protocols after installing it. To fix this, uninstall EpsonNet Config and then reinstall it.
Why am I unable to start EpsonNet Config with Web Browser for Epson Printer?
If you're unable to start EpsonNet Config with a Web Browser, it's likely because you haven't set an IP address for the network interface. To resolve this, set an IP address using EpsonNet Config for Windows or Macintosh, the printer’s control panel, or the arp/ping commands. You can check the IP address on a status sheet.
What to do if unable to set the IP address using the arp/ping commands on Epson 11880 - Stylus Pro Color Inkjet Printer?
If you're unable to set the IP address using the arp/ping commands, it could be due to a couple of reasons: 1. The network interface might not be connected to the network. Ensure the network interface is connected and check the network environment. 2. The printer might be located beyond the router. Make sure the printer and the computer are in the same segment.
General| Printer Type | Large Format Inkjet Printer |
|---|---|
| Maximum Print Resolution | 2880 x 1440 dpi |
| Maximum Print Width | 64 inches |
| Connectivity | USB 2.0, Ethernet |
| Media Handling | Roll Paper, Cut Sheet |
| Ink Colors | Cyan, Vivid Magenta, Yellow, Light Cyan, Light Black, Vivid Light Magenta |
| Media Types | Photo Paper, Fine Art Paper, Canvas |
| Interface | USB 2.0, 10/100Base-TX Ethernet |
| Operating Systems | Mac OS |
| Media Sizes | Roll: 17 to 64 inches |
Steps for installing necessary network components like TCP/IP for Windows Vista, Windows XP, and Macintosh.
Instructions for connecting the printer's network interface to the network and configuring its settings.
Procedures for installing the printer driver on computers for network printing in Windows and Macintosh.
Troubleshooting steps for problems with configuring the network interface or printing over the network.
Resolving issues where printing fails even after assigning an IP address to the computer and printer.
Solutions for problems encountered when starting EpsonNet Config, including protocol issues.
Troubleshooting the 'no network installed' message when starting EpsonNet Config.
Addressing the message "Could not complete communicating configuration data" during settings.
To Next Page
