Epson ET-2750 - User Manual

Start Here
12 When the message to start initialization appears on the
LCD screen, press the start button to start charging
the ink. Ink charging takes approximately 10 minutes. A
message appears when ink charging is complete. Press
the OK button to continue.
Note: After some ink is used for charging, the rest is available for
printing.
Caution: Do not turn off the product, raise the scanner unit, or
load paper while the product is charging or you’ll waste ink.
13 To complete filling the ink tanks, repeat steps 1 through 6
using the remaining ink in the bottles.
Note: Replace the bottle cap before disposing of the bottles.
14 Close the ink tank cover and scanner unit.
15 Select Maintenance > Reset Ink Levels, then follow the
on-screen instructions to reset the ink levels.
16 Follow the on-screen instructions to adjust the print
quality. Press the OK button to continue.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
3
Load paper
See the online User’s Guide for information about loading
capacity and available paper types and sizes.
1 Make sure the product is not charging. Then flip the
feeder guard forward, raise the paper support, and tilt it
backwards slightly.
2 Slide the edge guides all the way out.
Read these instructions before using your product.
Note for Spanish speakers/Nota para hispanohablantes: Para
obtener instrucciones de configuración en español, consulte la Guía
de instalación en www.epson.com/support/et2750sp (requiere una
conexión a Internet).
1
Unpack
Note: Do not open the ink bottles until you are ready to fill the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1 Remove all protective materials from the product.
2 Lift up the scanner unit. Remove all protective materials
from inside the product.
Caution: Do not touch the flat white cable or the ink tubes and
their translucent cover.
2
Fill ink tanks
Note: This product requires careful handling of ink. If ink spills, wipe it
off immediately with a damp towel to avoid permanent stains. If ink gets
on your clothes or belongings, it may not come off.
Warning: Keep the ink bottles out of the reach of children and do not
drink the ink.
1 Open the ink tank cover, then open the cap for the ink tank
you are going to fill.
2 Unpack one of the ink bottles. Hold the ink bottle upright
and slowly turn the bottle cap to remove it.
Caution: Do not shake or squeeze the ink bottles. Do not touch
the top of the ink bottle after its cap is removed.
3 Position the top of the ink bottle along the slot in front of
the filling port, then slowly stand the bottle up to insert it.
Note: Refer to the color-coded sticker on the ink tank unit to
identify the color of each tank. Do not force the bottles into
position; they are keyed for each color.
4 Wait for the ink to fill the tank. Do not squeeze the bottle.
Ink flows into the tank and stops automatically when the
ink is filled to the upper line.
Note: If ink does not flow from the bottle, lift and reinsert the
bottle.
5 When the ink tank is full, remove the ink bottle and
securely close the ink tank cap. Place the remaining ink
aside; you will need it later.
Note: Replace the bottle cap and tighten it.
6 Repeat the previous steps for the other colors.
7 Close the ink tank cover and then the scanner unit.
8 Connect the power cord to the back of the product and to
an electrical outlet.
Caution: Do not connect to your computer yet.
9 Raise the control panel, then press the power button to
turn on the product.
Note: If an error message appears, turn off the product and
check that no protective material has been left inside the product.
10 Press or to select your language on the LCD screen,
then press the OK button. Follow steps 11 and 12 to
continue ink charging.
Note: You can change this setting later using the product’s
control panel. For more information, see the online User’s Guide.
11 When the message to see the Start Here sheet appears
on the LCD screen, press the OK button. On the next
screen, press and hold the help button for 3 seconds.
ET-2750

Summary

Unpack the Printer

Remove Protective Materials

Remove all protective materials from the product before proceeding with setup.

Lift Scanner Unit

Lift the scanner unit and remove all protective materials from inside the product.

Fill Ink Tanks

Prepare Ink Bottles

Open ink tank cover and caps. Unpack ink bottles and remove caps slowly.

Insert Ink Bottles

Position bottle top along slot and stand upright to insert ink into the tank.

Ink Filling and Initialization

Ink fills to upper line. Start initialization process on LCD screen.

Complete Ink Filling and Settings

Repeat filling, close units, reset ink levels, and adjust print quality.

Load Paper

Prepare Paper Feed

Flip feeder guard, raise paper support, and tilt backwards.

Insert Paper

Load paper with printable side up in the rear feed slot and adjust edge guides.

Finalize Paper Loading

Pull out the output tray and select paper settings on the control panel.

Install Software

Prepare for Software Installation

Ensure the printer is NOT connected to the computer before starting setup.

Run Setup Program

Insert CD or download and run the product's software package from the website.

Configure Connection

Select wireless or direct USB connection and follow on-screen instructions.

Mobile Printing Options

Connect Devices for Printing

Print from smartphone, tablet, or computer using Epson iPrint or Epson Connect.

Troubleshooting Common Issues

Network Setup Problems

Verify network name, restart router, ensure 2.4 GHz is enabled, or check firewall.

Print Quality Issues

Perform nozzle check and clean print head if lines or incorrect colors appear.

Support and Resources

Product Screen Dark

Ensure the product is turned on and press any button to wake it from sleep mode.

Setup Connectivity Issues

Verify the product is on and securely connected via USB cable.

Access User Guides and Support

Find basic info, troubleshooting, warranty, and technical support online or by phone.

Epson ET-2750 Specifications

General

Print Technology	Inkjet
Print Resolution	5760 x 1440 dpi
Paper Capacity	100 sheets (plain paper)
Functions	Print, copy, scan
Print Speed (Black)	10.5 ppm
Scan Resolution	1200 x 2400 dpi
Ink Colors	Black, Cyan, Magenta, Yellow
Dimensions	375 x 347 x 187 mm
Connectivity	USB, Wi-Fi, Wi-Fi Direct
Duplex Printing	Yes
Scanner Type	Flatbed
Display	1.44 inch color LCD
Print Speed (Color)	5 ppm
Paper Sizes	A4, A5, A6, B5, Letter, Legal, Envelopes
Weight	5.5 kg