7 Repeat the previous steps for the other colors.
8 Close the ink tank cover.
9 Raise the control panel, then press the power button to
turn on the product. The power light ashes.
Note: If an error code appears, turn o the product and check
that no protective material has been left inside the product.
10 Select your language, country, date, and time settings.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
11 When an Epson Smart Panel setup message appears on
the LCD screen, select the option to continue setup.
12 When the message to see the Start Here sheet appears
on the LCD screen, press and hold the help button for
5 seconds.
13 Press the start button to start ink charging. Ink charging
takes about 11 minutes.
Note: When the power light stops ashing, ink charging is
complete. Once initial setup of the printer is complete, you can
top o the ink tanks with any remaining ink. See the online User’s
Guide for instructions.
Caution: Do not unplug or turn o the product, or open the
inner cover while the product is charging or you’ll waste ink.
Note: After some ink is used for charging, the rest is available for
printing.
14 Press the OK button to proceed with initial setup.
IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online User’s
Guide.
Important Safety Instructions: When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
• Do not use the Epson
®
product near water.
• Always keep this guide handy.
• Avoid using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution: To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
1
Unpack
Note: Do not open the ink bottles until you are ready to ll the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1 Remove all protective materials from the product.
2 Connect the power cord to the back of the product and to
an electrical outlet.
Caution: Do not connect to your computer yet.
2
Choose a setup method
The Epson Smart Panel
®
app can help you set up your printer
through an interactive, step-by-step process using your
smartphone or tablet.
If you do not want to
use a mobile device for
setup, skip to the “Fill ink
tanks” section.
To use your mobile device
for setup, continue to
step 1.
OR
1 Download the Epson Smart Panel app
from your device’s app store. Do not
launch the app yet.
2 Hold the power button until it lights up to turn on the
product.
Note: Do not connect your product to your computer yet.
3 Launch the app and follow its instructions to set up your
product. If necessary, tap the
+
icon on the top right
corner of the app’s home screen, select the option to set
up a new product, and follow the instructions to set up
your product.
For information on setting up the fax, connecting your product
to a computer, using voice-activated printing, solving problems,
or for details on reaching Epson support, see the sections on
the back of this sheet.
3
Fill ink tanks
Warning: Keep the ink bottles out of the reach of children and do not
drink the ink.
Caution: This product requires careful handling of ink. If ink spills,
wipe it o immediately with a damp towel to avoid permanent stains.
If ink gets on your clothes or belongings, it may not come o.
Note:
• Epson cannot guarantee the quality or reliability of third-party ink.
• Use the ink bottles included with the printer to set up the product.
Part of the ink will be used to charge the printhead. These bottles
may print fewer pages compared with replacement ink bottles.
• Epson strongly recommends the use of genuine ink to ensure
optimal print quality and performance.
1 Open the ink tank cover, then open the cap for the black
(BK) ink tank.
Note: Refer to the color-coded sticker on the ink tank unit to
identify the color of each tank.
2 Unpack the black (BK) ink bottle. Hold the ink bottle
upright and slowly turn the bottle cap to remove it.
Caution: Do not shake or squeeze the ink bottles. Do not touch
the top of the ink bottle after its cap is removed.
3 Insert the ink bottle into the lling port, as shown below.
Note: Do not force the bottle into position; each bottle is keyed
for each color.
4 Wait for the ink to ll the tank.
Do not squeeze the bottle or
allow it to contact any other
surface.
Note: Ink ows into the tank and
stops automatically when the ink
tank is lled to the upper line. If ink
does not ow from the bottle, lift and
reinsert the bottle.
5 When the ink tank is full, remove the ink bottle and
securely close it with the bottle cap. Place the remaining
ink aside; you will need it later.
Note: Do not leave the ink bottle inserted; otherwise the bottle
may be damaged or ink may leak. If any ink remains in the bottle,
store the bottle upright and top o the ink tank after completing
initial setup.
6 Securely close the black ink tank cap.
Start Here
ET-4810
To Next Page
Need help?
General
