Epson PowerLite 1760W User Manual (English)

Other manuals for Epson PowerLite 1760W

Operation Guide50 pages

Quick Setup Guide4 pages

Declaration Of Conformity4 pages

Maintenance Guide2 pages

Installation Handbook4 pages

Questions and Answers:

R
Roy GregoryAug 22, 2025
How to fix Epson Software when projectors cannot be monitored or controlled?
- M
  matthewsmithAug 22, 2025
  If Epson projectors cannot be monitored or controlled, first, ensure the network cable is correctly connected; reconnect if necessary. Check the Network configuration settings. Next, uninstall and reinstall EasyMP Monitor. Then, register the projectors you intend to control or monitor. Finally, verify that the projector's Standby Mode is set to Communication On (or Network On) or Network Monitoring is set to On in the configuration menu. When the projector is in standby mode, the projector's Standby Mode must be set to Communication On (or Network On) or Network Monitoring must be set to On in the configuration menu in order to use EasyMP Monitor to monitor and control the projector.
M
michaelhayesAug 23, 2025
What to do if an e-mail message is not sent when a problem occurs with an Epson Software projector?
- A
  Andrew KnoxAug 23, 2025
  If an e-mail message isn't being sent when a problem occurs with an Epson projector, check that the SMTP server IP address, Port Number, and Recipient mail address have all been set correctly. Also, ensure the projector's Standby Mode is set to Communication On (or Network On) or Network Monitoring is set to On in the configuration menu. If a critical problem has caused the projector to momentarily stop working, it cannot send e-mail messages; in this case, if the projector cannot be reset even after it has been checked, contact Epson.
E
ethan29Aug 25, 2025
Why am I getting an error message when starting up Epson EasyMP Slide Converter?
- A
  amy43Aug 26, 2025
  If you receive an error message when starting the Epson EasyMP Slide Converter, it could be due to several reasons. First, your operating system might not be compatible, so you should update it to the required version or install the software under a supported OS. Second, PowerPoint 2002 or a later version might not be installed; reinstall EasyMP Slide Converter after installing PowerPoint. Also, close PowerPoint before converting the file, as running PowerPoint can interfere with the conversion process. Finally, ensure you have write access to the specified folder and sufficient space on the drive to save the file or transfer the scenario. Delete unnecessary files to free up space if needed.
W
whiteanthonyAug 27, 2025
What to do if I cannot play scenarios in Epson Software?
- J
  Jason WatsonAug 27, 2025
  If you cannot play scenarios, it may be because the projector's resolution is XGA, while the scenario is set for WXGA (1280 x 800 dots). To resolve this, convert the PowerPoint file to an XGA (1024 x 768 dots) scenario file before projecting.
B
Brenda StephensonAug 27, 2025
How to fix 'Convert to FSE' not displayed in the PowerPoint right click menu for Epson Software?
- J
  Jeremy WilliamsonAug 27, 2025
  If 'Convert to FSE' is not displayed in the PowerPoint right-click menu after installing Epson EasyMP Slide Converter, it may be because PowerPoint was installed after the EasyMP Slide Converter. To fix this, reinstall EasyMP Slide Converter.
C
Christina BellAug 29, 2025
What to do if I cannot convert to a scenario in Epson Software?
- E
  Ernest HernandezAug 29, 2025
  If you cannot convert to a scenario using Epson Software, ensure that PowerPoint is closed before starting the conversion. Additionally, check that the Slide View setting is set to 'All,' as conversion is not possible when Slides or Custom Show is selected.
T
tonya84Sep 1, 2025
Why is my Epson software showing an error message when starting up EasyMP Network Projection?
- C
  catherinesellersSep 1, 2025
  If you receive an error message when starting EasyMP Network Projection, try the following: 1. Attempt to connect again. If the problem persists, verify the network settings on both your computer and the projector via the projector's Network menu. 2. Check the Projector Keyword displayed on the LAN standby screen and enter it. 3. Note that you may be trying to connect to a projector already connected to another computer. Clicking 'Yes' will connect your computer and disconnect the other. Clicking 'No' will maintain the existing connection. 4. Restart EasyMP Network Projection. If the message continues to appear, uninstall and then reinstall EasyMP Network Projection.
K
Kathleen OsborneSep 2, 2025
What to do if Epson EasyMP Network Projection image is not displayed or is slow to appear?
- S
  Sherry ByrdSep 2, 2025
  If the image is not displayed or appears slowly when connecting with EasyMP Network Projection: * Be aware that, depending on the computer, the movie playback screen in Media Player may not be displayed, and the screen saver preview may not be displayed normally. * The display speed decreases when WEP encryption is effective or multiple projectors are connected.
T
Timothy LeeSep 5, 2025
What to do if there is no audio from the Epson PowerLite 1760W Projector when connecting with EasyMP Network Projection?
- L
  Laura DudleySep 5, 2025
  If you're experiencing a lack of audio from the projector when using EasyMP Network Projection: * Remember that audio can only be transferred to one projector. Try disconnecting other projectors. * Ensure you have selected 'Output audio from the projector' on the Audio Output tab.
J
Janice BlairSep 6, 2025
What to do when an Epson connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection cannot be made from another computer?
- T
  Teresa PerkinsSep 6, 2025
  When a connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection cannot be made from another computer. With EasyMP Network Projection, the computer currently connected can be disconnected when another computer tries to connect to the projector. Therefore, when a Projector Keyword is not set for the projector, or if you know the Projector Keyword, you can disconnect the computer currently connected and then connect your computer to the projector. When a Projector Keyword is set for the projector and you do not know the Projector Keyword, restart the projector and reconnect.

Epson PowerLite 1760W Specifications

General

Contrast Ratio	2000:1
Lamp Life (Eco Mode)	10000 hours
Projection System	3LCD
Output Ports	VGA
Resolution	1280x800
Connectivity	HDMI, VGA, USB
Projection Size	30 - 300 inches
Input Ports	HDMI, VGA, USB
Keystone Correction	±30 degrees (Vertical), ±30 degrees (Horizontal)