Quick Setup
IMPORTANT: Before using the projector, make sure you read these instructions
and the safety instructions in the online User’s Guide.
Note: Your product may differ from the illustrations on this sheet, but the
instructions are the same.
Connect the projector
Computer
Choose from the following connections. See the sections below or the online
User’s Guide for details.
VGA cable
USB cable
HDMI cable
HDMI port
Connect one end of an HDMI cable to one of the projector’s HDMI ports and
the other end to an HDMI port on your computer.
Computer port
Connect one end of a VGA cable to one of the projector’s Computer ports, and
the other end to your computer’s monitor port. If you are using a laptop,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
USB port
Connect the square end of a USB cable to the projector’s USB-B (square) port.
Connect the flat end of the cable to any USB port on your computer.
Windows
®
7 or later: After turning on the projector, follow the on-screen
instructions to install the Epson
®
USB Display software (EMP_UDSE.EXE; only
on first connection). If the software screen does not display automatically, open
My Computer, Computer, or This PC, then double-click EPSON_PJ_UD.
OS X 10.8.x or higher: After turning on the projector, the setup folder for
USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection). If the software screen does not display automatically,
double-click EPSON_PJ_UD, then double-click USB Display Installer.
External monitor and speakers
You can connect an external monitor and external speakers to your projector to
enhance your presentations. See the online User’s Guide for details.
Wired network
Connect the projector to your network using an Ethernet cable. See “Wired
network configuration” on the back of this sheet for more information.
Microphone
Connect a dynamic microphone to the Mic port, using a 3.5 mm mini-jack cable.
Video device
Connect multiple video devices and use the Source Search button on the
projector or remote control to switch between them. For more information on
playing sound through the projector, see the online User’s Guide.
Component video
to VGA cable
Audio cable
RCA video cable
(composite video)
HDMI cable
Camera, USB device, or document camera
Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06
or DC-07 document camera to the projector’s USB-A (flat) port.
USB cable
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s PC Free feature. See the online User’s Guide for details.
Using the remote control
Install the two AA batteries as shown.
Choose which source
to display
Turn projector on
and off
Access projector menus
Turn off projector
display and sound
Access the Home
screen
Navigate projector
menus
Control projector
volume
For more information on using the remote control, see the online User’s Guide.
Turn on your equipment
1
Turn on your computer or video source.
2
Make sure the power cord is connected and plugged into an
electrical outlet.
3
Press the power button on the projector or remote control. The
projector beeps, and the Status light flashes blue and then stays on.
Note: To shut down the projector, press the power button twice.
4
If you don’t see an image, press the Source Search button on the
remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
5
Use the arrow buttons on the remote control to highlight any of the
options on the Home screen, then press to select it.
6
The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Management and press . Select Language and press . Select your
language and press . Press the Menu button to exit the menu system.
Adjust the image
1
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
2
To reduce or enlarge the image, press the T (tele) or W (wide) button on
the projector.
3
To sharpen the image, turn the focus ring.
4
If your image looks like or , you may have placed the projector
off to one side of the screen at an angle. Place the projector directly in
front of the center of the screen, facing the screen squarely. If you can’t
move the projector, use the horizontal keystone slider on the projector to
correct the image shape.
5
Your projector automatically adjusts an image that looks like or ,
but if necessary you can press the or button on the projector to
correct it.
Wireless network
configuration
Follow these steps to set up the projector for a wireless network connection.
1
Press the Menu button on the remote control.
2
Select the Management menu and press .
3
Select On as the Wireless LAN Power setting.
4
Select the Network menu and press .
PowerLite
®
EB-L200SX/EB-L200SW
To Next Page
Need help?
General